Search results

  1. BowPro

    Lowrance Elite FS 9

    Bought a boat and this sonar came with it. Tried a reset, uploaded the latest software version, and played with all of the settings to no avail. The down scan is a snowy haze as well. The transducer is the 3 in 1, as shown on the tag of the transducer cord, and it is also showing as a 3 in 1...
  2. BowPro

    E70TLEDA Primer Choke

    Is there a rebuild kit for the existing primer choke I have, or do I need to just buy the whole new part? It appears the replacement part number used to be 0437238, but now replaced by 5007356. It leaks fuel. If there is a gasket rebuild for this, I'd rather just do that, but I can't seem to...
  3. BowPro

    1990's Evinrude 70 horse

    My son got a free boat for cleaning all of the garbage out of it and cleaning out a small barn full of garbage. Got it prepped, steering cable unseized, Sea foam deep creeped the cylinders, pulled the carb bowl screws and pumped Seafoam until the crud was removed and Sea Foam drained, etc. Rolls...
  4. BowPro

    Powerhead Down!

    2005 Evinrude 225 HO DI. Running down river and lost a lot of power, it slowed down immediately, and I could hear knocking. I shut it down and then tried to start it just to see what it would do. It was locked up. About 5 minutes later, after cooling down, it started up, but had the knock. I...
  5. BowPro

    Evinrude Model Number??

    I have a 2004 Evinrude 225 HO Direct Injection. My model number on the plate says E22FHLSOB. I can't find that number in a google search, nor in any parts diagram sites. The closest one to it is E22FHLSRM. Maybe this one corresponds to it?
  6. BowPro

    Cable clips

    I have carpeted rod boxes and didn't want to drill holes up in the inconspicuous spot to run cables to the bow. These buried into the carpet very well and are holding the cables out of the way and hidden. Super quick and effective install and can easily be removed or moved. I also broke the...
  7. BowPro

    Aerator Timer for Triton

    Where can I get the original aerator timer for a 2004 Triton TR21x? It's a dial knob. The first click is "manual" mode. The clicks thereafter are the timers.it only works in manual mode. I have searched but can't find anything that looks like an oem replacement. Is there a place that supplies...
  8. BowPro

    2004 Evinrude 225 DFI oil mix

    Never owned an Evinrude. Picked up a 2004 Triton TR21X after mechanic gave the outboard a clean bill of health. Now, for the oil. Someone mentioned these outboards are programmed to run a particular oil mix. I have no clue what they're saying. I don't want to just settle with Quicksilver dfi at...
  9. BowPro

    Windshield

    I have a 2002 Skeeter ZX190. Where can I find a replacement windshield/windscreen, or whatever it's called? Thank you.
  10. BowPro

    Pressure (peeing) with hose attached

    Put the ears on the Vmax 150 today and the pee is strong from the tube, but there was no reading on the pressure gauge. I removed the cover to the pressure control valve and checked the spring and valve. That was all I did. I got the hot light a few years back and the pressure control valve was...
  11. BowPro

    Find My Topic

    I started a thread asking about a Yamaha tilt/trim part. Someone replied with the correct diagram that included the part I needed. How do I find my past posts so I can retrieve that reply that I'm looking for. I can't seem to find my thread history. Thanks in advance
  12. BowPro

    Tilt/Trim seal parts

    I have replaced one of the trim seals on my P150TLRW, having to buy the screw (cap) due to destroying the original from it being on so long. The seal on the center shaft i starting to leak a little now, and I want to replace the seal. Looking on the parts diagram, I don't see the cap being a...
  13. BowPro

    Heat Buzzer Yamaha 150Vmax Outboard

    Tell me if my speculation is correct: Put boat in the water. idled away from ramp as I was getting rods and reels ready. About two or three minutes out, I got the buzzer. I shut it off and used the trolling motor to fish the park. It's a no wake lake regardless. I thought it might have been low...
  14. BowPro

    What is this?

    It's mounted on the transom
  15. BowPro

    Lowrance HDS8- What Generation Unit Do I Have?

    I bought the used boat with the Lowrance HDS 8 several years ago. I went on the Lowrance website recently to download the software update. I was told if the Lowrance is a Gen 2, it will say Gen 2 on the start up screen. Mine says nothing about that, so I'm assuming it's a gen 1. Looking at the...
  16. BowPro

    Gear Lube or 2 Stroke Mix?

    It's a new lower unit. Saw this leak. Pulled lower plug on lower and did not observe any water come out. This fluid looks and smells identical to the lower lube, and it looks and smells identical to the Yamalube 2 stroke fuel mix as well. I have heard that the excess, unburned fuel mix can exit...
  17. BowPro

    NGK Marine Plugs

    I was told to make sure I could run NGK marine plugs before I install them because some outboards specify not to use them. I don't understand the logic behind possibly not being able to use them, but I'm gonna ask anyway. I'm running a Yamaha Vmax 150 2 stroke. It's a 1998 (serial numbers...
  18. BowPro

    Finding your year model and engine by the numbers on your motor.

    These two links below I stumbled upon helped me out drastically and I thought I would share. The PDF file is a guide to tell you the specific Yamaha motor you have on your boat. EX. The Numbers on my motor are P150TLRW (use my numbers and look at the 1991 to 2005 chart)... Looking at the...
Top