Search results

  1. vince59

    D6-370 workshop manual

    Hey all, is there any possibility to get a copy of the workshop manual for D6-370 engine? Thnaks for any help!
  2. vince59

    Mercury Marine Tilt Trim Limit 899625K06 installation instructions

    Hey all, is there any source of information available in the forum about installation of mentioned kit? Thank you very much for any help
  3. vince59

    KRAUS & NAIMER C26 4 positions wiring diagram

    Hey all, I installed an inverter on a Boston Whaler and I want to connect to the main switch panel. I have a KRAUS & NAIMER switch C26 and I ma looking for a wiring diagram for proper connections. It is a C26 with 4 positions, OFF / SHORE1 / SHORE 1&2 / GEN. Thanks for any help. regards from Italy
  4. vince59

    Verado 150 harness. Help for paddle wheel connector.

    Hey all, I have a Verado 150 with DTS whitout paddle wheel. I get speed and data from the GPS but I would like to install a paddle wheel to get extra data. I am not sure about the connector coming from the engine wiring. Searching into the hull I found a connector coming from the engina but I...
  5. vince59

    smartcraft DTS wiring ad power supply connection

    I have a smartcrafts DTS installed in my boat and I'm checking the wiring. I have two batteries and one engine. Connections are made so that smartcraft always gets power even if I set the battery switch to OFF. Mercury dealer told me that this is a requiremt in order to keep the system "alive"...
  6. vince59

    Mercury Verado 150hp workshop manual

    Hi, I do ot know if I can ask for help to get a workshop manual for a Mercury Verado 150 HP. I am not a professinal but would like to know something more about my engine. Any hel would be greatly appreciated.
  7. vince59

    vp aqad41a fuel consumption

    hallo, I am wondering if there is any device I can use to measure the actual fuel consumption? I was thinking to a device measuring flux but the diesel engine has a return circuit that makes it almost impossible. Does anybody have a fuel consumption chart for this engine? Thanks
  8. vince59

    VP oil cooler disassembling

    Because of a small water leakege on board I need to disassemble the oil cooler in the pic...any hint or trick ...I tried to gently hammer but no result...
  9. vince59

    dp290 trimming during navigation

    After more than 100 hours navigation with my shaft34 I realized that we had to keep the trim down (-5/-6) to have the optimum speed and bow height. I am wondering if navigating for long time with trim down could have any harmuful effect on the stern drive mechanism (dp290a)...any idea about?
  10. vince59

    AQAD41A oli cooler mainteinance

    after more than 100 hours I am doing some mainteinance. As you can see in the enclosed picture I had some salt water coming in from the oil coolerbut no problems at all. Do you have any tip or trick for this kind of job? Engine is a AQDA41A has anybody step-by-stepdismounting instructions? Thank...
  11. vince59

    wave runner gp1300r service manual

    ..not sure if I can post the question...is there any place where to download the service manual for the gp1300r pwc? Thanks
  12. vince59

    vp aqad41a

    I want to check if the rpm gauges are working properly. What kind of instrument do I need and how do I connect it to the engine?
  13. vince59

    volvo penta propeller...

    I have a bunch of propellers and I am looking for having a good set for my boat however I can't get the equivalence between the propellers because I only have the A6, or B6 and so on...is there a kind of comparison chart were tolook to get the pitch and diametre value for each volvo penta type...
  14. vince59

    aqad41a-dp290...best rpm range

    well...after spending some time for checking that everything was ok last work was the water pump gasket...the boat was back in the water last saturday. We tested the boat in a short run and we had good performance up to 3500 rpm (we have a A7 propeller) and good sound form the old diesel 6cyl...
  15. vince59

    can anybody help to understand what this instrument is?

    as per title please find a pic
  16. vince59

    workshop manual for AQAD41

    hallo to everybody, I am from Italy and new to this forum. I am confident that foreign forums are pretty reliable and I am reading through the threads to get information for my engines. I have a vintage shaft34 with two aqad41 200hp and I am working to put them in the water as soon a possible. I...
Top