Search results

  1. P

    1998 115hp Fastrike

    Ok folks picked up this motor for dang near nothing...$250. Lower unit has less than 30hrs on it. I have to fix one hole on it. Lost compression on one hole but motor does in fact still run. It has an ignition system that I am not at all familiar with. Its called an OIS system. Here again I am...
  2. P

    2002 40hp 2 stroke

    Trying to help out a friend. He has a 02 40hp Merc 2 stroke that runs fine for a few times out then its back to the bench. Pulls the carbs cleans them up and off and running again. Everytime he has problems with it there is oil dripping every where on the carb throats ets... All fittings are...
  3. P

    New Tack installation

    I purchased a new tack for my boat and it never had one installed from the factory. I was told there is a wire I need to move under the engine cowling. The yellow/gray wire is to be moved to the pole conating the gray wire . Is this correct. My motor is a 1994 90hp evinrude. I also purchased the...
  4. P

    Might sound stupid but......

    I have started restoring a high performance bass boat and already know that I have to remove the cap to get to the area that needs replacing. I am a bit fuzzy on this. After I remove the cap I know that I have to replace the stringers and transom. My question is grind all the glass of the...
  5. P

    94 crossflow tack install

    Got a boat that has no tack on it. Was not installed from the factory. Bought a tack and need to know which wires to hook them up to. Its a 94 model rude 90hp V4. Any help will be greatly appreciated.
  6. P

    90hp evinrude

    I own a 90hp evinrude and this being my first rude need some info on this motor. The serial number is 03530467 and the model number is E90TLERC. What I need to know is this a looper or a crossflow. All I can tell right now is that its not the bubbleback design it is the flatback design. Also...
  7. P

    1994 Evinrude prop

    Got a 1994 Evinrude on a 16ft Tidecraft bass boat. Not real familiar with OMC's as this is the first one I have really tried to get the best outta it for the size. Right now according to the faria gauges I am using in the boat 44mph is the best at5300rpm's. Has a dang ole stinray stabilizer on...
  8. P

    Wiring in a switch for 12/24 volt trollers

    I need to know where I can get a schematic for wiring in a switch on the bow of my boat so I can put the batteries on charge without having to disconnect them all the time. Ifn you know where I can get this it would be greatly appreciated.
  9. P

    1993 or 94 90hp

    Ok all u motor guru's need some help. Gotta 1993 or 4 90hp evinrude and dont know what motor it is. Is this a crossflow or a looper and also it is it one of the 60 degree blocks. I am no OMC man so I really appreciate the help guys. Gott figure out which motor this is cause I am gonna up the...
  10. P

    40hp Mariner What year is it???????

    I got a Mariner 40hp cyl 2stroke with a magneto style with points ignition. I am sure that the serial number is 676S100246. Now I found stamped on 2 places on the block 67600 and thats it. I know the motor was made by yamaha but I still need to knwo the year of this motor to get correct parts. I...
  11. P

    Late 80's 115hp Rude With a Cold

    Got a Late 80's 115hp bubbleback Rude that has developed allergies ie sneezing and not running well at WOT. When it first started I figured it was time to rebuild carbs so took care of that issue. Now you couldnt ask for a faster starting engine be it cold or hot. Will idle like a champ but now...
  12. P

    Mariner/Yamaha Igntition problems

    Dont want to double post but I need help with a Mariner/Yamaha. Right now it has the point style ignition. The top coil has quit firing. I think I need a ignition source coil(the one under the flywheel) and a primary coil (the one on the block. I have installed a new set of points. The motor is...
  13. P

    1976 115hp Johnson Coils

    I have a 1976 115hp Jonny that is in bad need of coils. I have located a set that the person would sell me 4 of them for a VERY nice price compared to new price. My question is they are not the green coils with the metal plates around them but they bolt up the same and have the plug wires coming...
  14. P

    40hp Mariner/Yamaha ignition problems

    Due to the fact of the cost and availability I am contemplating changing over my late 70's early 80's 40hp mariner/yamaha from points style ignition to the stator type ignition. I have located a stator plate with all the necessary electonics on it for a VERY reasonable price. My question is do i...
  15. P

    Early model 40hp 2Stroke cyl Mariner

    First off cant find out what year my mariner 40hp 2stroke 2 cylinder is. The serial numer is 676S100246. I do know that it is the one made by yamaha. What I am looking for and cant seem to locate is a water pump impellar and set of coils for this motor. I have the numbers off of the coils that...
  16. P

    Early 80's 50hp Merc Upper Motor Mounts

    My manual is really vague so I need some instructions. I need to replace the upper motor mounts on my 50hp. I removed the lower pan I beleive it is called but still cant see the motor mounts. I have been told that I can hang the powerhead without removing all the wiring etc.. So my question is...
  17. P

    115hp Jonny

    Is there an online site that I can go to to cross reference my serial number and find out the exact yearn of my motor. Both service manuals that i have but no serial number identification as to what year it is. Need to know this so that I may set this motor to that years exact specs. Thanks for...
  18. P

    Editing my first post

    I found the mariner site but still cant find out what year this 40hp mariner (yamaha made) is. The serial number is ..676S100246. If anyone noes PLEASE help me so that I can get the correct manual. I have already bought one and with my luck it was the wrong run. 35.oo down the toilet oh well...
  19. P

    PLEASE HELP ME

    I found on your site a place to identify what year Merc I have, but all I can remember is it was bighammer something. Could someone PLEASE email me or post that site again so I can save it this time. I am also looking for a site that contains the same content for Mariners of the early to mid...
  20. P

    Need Help Identifying What year????

    I know this sounds abit crazy but this year I have purchased 2 Mercurys and 1 Mariner. I know the year models close but not exact. Does ANYONE know where I can go to online and find out exactly what year these motors are so that when I go to my Seloc manuals that I tune these motors I do it...
Top