Search results

  1. R

    1999 200HP OX66 surging/cutting out

    Hey folks, I have a 99 model 200HP 3.1L ox66 yamaha outboard, motor has ran awesome for the past 5 years, took it out saturday and if I ease into the throttle and keep it under 1/3 throttle itll run and drive all day. If i try to floor it or push it over that point it'll fall on its face, and if...
  2. R

    1992 evinrude spark issues

    Hey folks I have a 1992 evinrude 200hp xp model# ve200slens I thought I had no spark, pulled all the plugs and I have spark on cylinder #4 that's it. I've disconnected the red plug,no change. I've disconnected both kill wires no change starter turns the motor over healthily compression is...
  3. R

    Skeeter top cap decals

    Hey guys I have a skeeter zx202c, I lost one of my decals off the side of the boat and I am looking to replace them. I'm not sure where i can get the raised domed oval decal, but i have considered using a skeeter sticker instead. Anyone have any pictures of their boats with decals or logos on...
  4. R

    1976 55hp johnson dies when put in gear

    Hey guys I've gotta 1976 55hp Johnson motor, 2 cylinder with great spark to both plugs. I've tried different tanks. And this has me at my wits end. I can start the motor and itll idle all day long, but when put into gear it falls on its face and dies, only way I've been able to keep it going...
  5. R

    Carpet alternatives?

    Hey guys. I've got a 1999 skeeter zx202c. I don't bass fish and my carpet always ends up covered in fish slime (catfishing) what would be some good alternatives when I go to replace it, or should I just stick to carpet?
  6. R

    Bad day.....broken ox66 3.1l

    Hey guys, had a bad day yesterday boat jumped the chocks when I was unlocking it from the truck. Rolled down the hill into a fence, broke a few things scratched up my cowl and midsection a bit. Busted one fin on the side of the lower also.... I can not seem to find this steering arm..... any...
  7. R

    1998 19' Challenger Center Console (Seat Question?)

    Hey folks, I stumbled upon a 1998 Challenger by Kencraft? it's a 19' center console, with a 150 XR6 on it. Going to look at it this weekend, my question is this.... The "Back rest?" that you would lean back against on the front of the console is missing, is there a place I can order that piece...
  8. R

    1997 50tlhv Yamaha carb adjustment

    Hey guys, got a 1997 50hp yamaha that I need to adjust the carbs on, before I got it it had a someone messing with all the linkages and screws. Got the carbs cleaned and linkages lined out, but it's idling really high, it's got a screw in each carb. Could anyone give me an idea where to start...
  9. R

    3.1L ox66 Squeak

    Hey folks, Just started noticing a "squeak/squeal?" sort of sound from my 200 3.1L OX66 1999 model, seems to be more apparent in gear, can't really hear it at WOT, but at idle it's very noticeable, doesn't seem to do it at the beginning of the trip..... It seems to show up after running it for...
  10. R

    1982 150hp blackmax powerhead swap issues

    Hey folks, I picked up a used powerhead to swap onto my midsection, checked compression and spark 120PSI on all 6, spark on all 6. Got the motor onto my midsection, and bolted on. Swapped known good carbs, and powerpacks onto the engine. Put it onto the hose, fired it up sat there and idled...
  11. R

    Difference in these two props?

    I'm looking at a solas 4blade prop to run on my 3.1L yamaha, just to pull tubes/ski's. Looking at the 23P Amita 4. There is a Mercury Version, and a Yamaha Version. Am I incorrect in thinking that Yamaha and Mercury have interchangeable props? I know I have personally ran my old 21P Solas on...
  12. R

    200hp 3Ox66 rpm loss

    Hey folks, got a 1999 3.1l ox66 200hp efi engine. It hasn't gave me any major issues to date. However I got on the lake today and noticed about a 6-800 rpm loss at wot, about 8mph on the top end. Got home checked the compression, 110 across the board on my China made gauge (same compression as...
  13. R

    Helix 7 Side imaging transducer location

    Hey guys. I picked up a helix 7 si gps chirp g2 unit, first time I have owned or installed a si unit. I googled for 3 days waiting for it to come in. Cables routed correctly. And then I mounted the si transducer just below the step on my transom and went and tested it. It looked amazing. Under...
  14. R

    Ox66 200 cylinder pictures help?

    Hey guys. I got a endoscope off eBay and took some cylinder pictures of this 98 ox66 200 I have. Can anyone look at these and tell me if it's something to worry about? It looks like a lot of carbon on the piston to me and there's a few spots that looks like carbon has flaked off. Anyone with...
  15. R

    1999 Yamaha 200HP OX66 Couple of Questions

    Hey guys, I picked up a 1999 Skeeter ZX202C last year, coupled with a 1999 Yamaha 200HP OX66. Fuel pumps were replaced early 2016, along with the lower unit they shelled around the same time they ran ethanol in it. I have done nothing, but throw gas, and oil (and seafoam/MMO) in every...
  16. R

    1970s 75hp chrysler

    Hey guys, I've got an early 70s model chrysler. Ill get the model/serial when the weather clears up on me. It has a distributor with points and an ignition coil i believe. The problem is its not getting any fire. I was told it ran before. Are there any troubleshooting tests i can do to try to...
  17. R

    1976 55hp johnson lower unit interchange

    Will a 1970 50hp lower unit swap into my 1977 55hp johnson ?
  18. R

    1977 55HP Johnson Outboard Lower Unit

    Does anyone happen to know what year/HP Range will interchange? A friend of mine had his lower go down on him over the weekend, and I've decided to help him search for a replacement. Thank you!
  19. R

    Ox66 200 low water pressure

    Hey guys, I know these motors hold lower water pressure at idle. Prior to today I was getting 2-5psi at idle and 18-20psi at wot. Today I am getting around the same at idle and around 10-13 at wot. The pissing stream is still strong and constantly there. There is water coming from the exhaust...
  20. R

    1999 Yamaha 3.1L OX66 200HP Prop Suggestions

    What would you guys suggest to run on this engine? Currently turns a 25P 3 Blade yamaha prop, but I think it could handle a bigger one. Running on a 20'7" Skeeter. The tach says somewhere around 6500RPMS (but I am almost CERTAIN that isn't right). There is a prop shop nearby, would it be worth...
Top