Search results

  1. B

    GSP Add On To Haswing

    I purchased my Haswing Trolling motor last year, and i now regret not getting the Anchor Lock. I've seen other GPS add on for Minn Kota, but is there anything i can add to mine for Anchor Lock? Or do i need to sell mine and purchase the right one?
  2. B

    9.9 Evidrude stalls when fully excellerated

    My 1989 Johnson Evinrude 9.9hp idles and starts up with no problem. When i go to give it some throttle is stalls around 3mph. Changed fuel line and bulb but still same thing. Thinking the carb needs a rebuild. Wasnt sure if there is an easier fix to try first.
  3. B

    Tow Ring Repair

    My Tow Ring busted loose on my 16ft Sylvan Aluminum boat. I was going to replace the broken rivets with bolts, but getting access to the inside of the boat looks terrifying. Would an epoxy like JB Weld and some new rivets hold?
  4. B

    1984 9.9 Johnson no ignition

    I've used this as my trolling motor. Had it out today and it Started up several times today no issues. Last time it ran when I started it, it took a couple turns of the key for it to fire up. Last time I tried to start it nothing. Checked the kill switch and battery connections. All look ok...
  5. B

    1964 sportsfour 60hp manual shift no forward

    After replacing the upper seal I now have no forward gear. It makes a clicking sound when I try to put it in forward. I checked the shift rod connector and bolts are tight.
  6. B

    1964 sportsfor spark plug order.

    I think I put the plug wires back in the wrong order. Is this an issue? I guess I will find out when I crank it over
  7. B

    Bad Seal? 1964 Evinrude 60hp

    I replaced the gear oil for winter. As I was pumping in the new oil i noticed gear oil coming out the water Intake. Is this a bad seal? I replace the prop shaft seal this summer. Should have replace the upper one as well.
  8. B

    Drive Pin Question

    I'm replacing the drive pin on my 1964 evinrude 60hp propeller. Its to long for the nut key to fit over. I'm guessing I have to cut it to length. Seemed weird to have to cut it. Any help would be appreciated.
  9. B

    No forward gear

    Just finished replacing the lower seal. All was going well until I barrel tested it. Now I have no forward gear. Reverse and neutral are fine. Its a manual shift 1964 60hp evinrude sportfour. Any suggestions would be helpful. I checked the shift rod connector and it looked ok.
  10. B

    Seal Placement

    Which side goes in first to the gear head, metal or rubber? Motor is a 1964 60 Hp.
  11. B

    Seal Placement

    Which end goes in the gear head first? Any special tips on putting it in without damaging it?
  12. B

    1964 Evinrude 60hp Sportsfour

    Noticed this gear oil leaking from the propeller. Does this require a seal replacement or am I to expect these issues with an older motor?
  13. B

    Mystery Hole leaking Oil

    I water tested my 1964 Evinrude after replacing the water impeller. I noticed this small hole next to the upper gear oil screw. It looks like it suppose to be there. There was a consistent leak of oil coming from it. Wasn't sure if this is normal or am i missing a screw.
  14. B

    What is this part? Off my 1964 water pump

    When pulling my water pump i noticed this inside my water pump housing. Looks like some kind of spring like O-ring. Not sure where it goes or if i need to replace something.
  15. B

    1964 Evinrude 60hp Sportsfour

    My first time here. Just purchased a 64' Evinrude Sportsfour 60hp. Runs and starts easy. Has a hair line crack in the lower unit. Was hoping some JB Weld would hold up. Was also wondering about the water discharge. Looks like it was just "spuddering" out the engine. Is that normal for...
Top