Search results

  1. mr gibbs2

    remote oil tank gauge

    hello i have a remote oil tank for a 200 hp evinrude year 2000 system check , really can't see the tank oil level by looking at it ,it has a remote fill . Don't want to fill it up to the filler tube top it may leek. can i run a gauge off the wiring harness to monitor oil level in the tank...
  2. mr gibbs2

    ox66 LOW pressure pumps leaking

    when testing LP pumps 1 undolt them from motor 2 squeeze primer bulb . result// seems gas is leaking out of the mounting holes to the pumps , not out of the hole that goes to block . Question Does the mounting holes have to be bolted together to do this test . motor bogs down at 3800 rpm ...
  3. mr gibbs2

    2001 ox66 250 sneezing

    fuel pressure 38 at idle today stays steady . last season change all filters, had injectors cleaned lift pumps replaced ran well last year. did not drain vst for winter . first time out runs poorly , sneezing stalls surges up then down and stalls , smokey , sent injectors out today for service...
  4. mr gibbs2

    2001 250 ox66 fuel issues

    I can here pump on and tank fills when I crank or when pump ball , and fires when I spray gas with oil into throttle body but no pressure on reading on gauge even with the valve removed, it only comes out at a dribble
  5. mr gibbs2

    250 ox66 2001 running poorly

    Was running rough , now not running . last Season replaced all 3 pumps all filters I can here pump on and tank fills when I crank or when pump ball , and fires when I spray gas with oil into throttle body but no pressure on reading on gauge even with the valve removed, it only comes out at a...
  6. mr gibbs2

    is the motor to low?

    is the motor to low ,im thinking one more hole up !
  7. mr gibbs2

    Crap on transom cracked

    Transom picks new project 1997 stratos 2100 center console going to repower with a newer motor . Took motor off and inspected holes all wood or what ever it is made of I don’t , no water intrusion can’t scrap anything out of it its hard , it after taking the aluminum trim plate it has a crack...
  8. mr gibbs2

    2002 250 ox66 compression

    thinking of buying a 2002 ox66 250 hp yamha getting out of the late 90s evinrude loopers . i found a motor with compression at 120 on all 6 cylinders tested my me with my gauge always on the money, the motor starts, runs good on the stand , unknown hours , no gauges . my question is , is...
  9. mr gibbs2

    timing v6 evi rude

    1990 200 hp evinrude . replaced power pack, timer base , sator,with digital cdi units ,and replaced flywheel . Runs as good as it always had before power pack went south , but starts at the flip of the key . top rpm is 5300 no hesitation but timing is off about 8 degrees with a test wheel in the...
  10. mr gibbs2

    Flywheel inner magnet

    1990 v 6 looper 200 Hp testing done with s Stevens cd77 evinrude not getting and volts out of port side of timer base , would a bad inner magnet only have voltage on one side ,the starboard side has volatage when cranking port none, is it the timing base or the flywheel
  11. mr gibbs2

    TIMER BASE SENSOR COIL TEST RESOULTS

    1990 200 HP EVINRUDE no spark now has been acting up , now no spark. output test using stevenes 77 neg on the port middle terminal . then red lead to the remaining posts. i get voltage on only one post while cranking motor all other nothing .the does that mean the timer base has failed sator...
  12. mr gibbs2

    Hydra sports,transom

    Just picked up my old 86 Hydrasports vector from the person I sold it to years ago ,as a project .it was a great boat. however I know the transom is de laminating on one side it's wet . , there is no flex or cracks but it been wet many years as a result of how the live well fitting was...
  13. mr gibbs2

    Older rubber hub ss viper prop on newer v6

    Hello all ! have a very nice older viper prop that I want to put on my 2001 Johnson 200 hp v6 .the aluminum prop on it now has the newer hub system and the thrust bushing dosent push out the viper prop enough to turn free . Is there a trust bushing that would allow me to use this prop thanks.
  14. mr gibbs2

    Re core gunell

    Re cored gunnel and and having a tuff time Finishing it off . Are there any tricks to using epoxy over head ? I can't seem to get it to tack and stick and making a mess . I'm using west system slow hardener . the repair is solid but I would like to make it look good . I recorded it with 1/2...
  15. mr gibbs2

    Rotted core under acess plates

    I was going to caulk under acess plates and when i took it apart , not good the area is bumped out underneath about 1 foot by 18 in and stops on all 4 sides . I've cleaned out almost all that is damaged and cleaned it with actone and will rough it up wit sand paper . Any recommendations on...
  16. mr gibbs2

    Gell coat cracks

    Any recommendations on repairing spider crack on my boat ? Should I just have a shop do the whole top deck ,or try or repair it myself ,I've done some fiberglass work but this need to look good thanks
  17. mr gibbs2

    Temp gauge 2001 v6 looper

    Just brought another boat it has a 2001 200 Hp Johnson looper on it with 200 hours and I want to know if I can put a temp gauge on the dash for my motor without running a new wire from the heads with a bolt on Senser . Is there any way to use the wires under the dash ( harness ) to pick up the...
  18. mr gibbs2

    Transom repair

    Hello having a issue with my raft just noticed the cracking or the transom mounts .has any one have any advice on how to repair this.?i don't want to have to take it all apart can I just build up layers using rubber or pvc fabrics going from small to large . I'm totally new at this but always...
  19. mr gibbs2

    Smoking by exaust

    1987 460 giving me a headache , under way at 3000 rpm or higher their is smoke coming from the starboard side below valve cover ( smells like oil ) throught it may be a exaust leak . Changed the exaust gasket and the valve cover gasket still the problem persists . The valve cove gasket is the...
  20. mr gibbs2

    Trailer cable strength

    Hello ,I have a 23 foot grady white gulfstreem weighing a little over 6000 pounds with gas and gear on a 8800 pound load roller trailer . I need a winch cable that will do the job .the cables I see for sale are 1/4 diamater and 5000 pound breaking, but 1400 pounds working load ,what does that...
Top