Search results

  1. L

    2009 Tohatsu 20hp - Oil Cap Melted

    I was running my boat through a bunch of hydrilla weeds at low speed, when I saw a lot of smoke coming out of the motor. The red warning light was also flashing. I shut the motor off and dunked the hot cover into the water to cool it. The yellow oil filler cap had melted and blown off and was...
  2. L

    Replace Tohatsu 9.8 with 20hp - Same transom fit?

    I have a 2007 Tohatsu 9.8 four stroke on my antique 14' runabout. Great little motor, but I need more power. The new Tohatsu 20hp motor looks good. My question is if the transom bracket is the same for those two motors, or will I have to drill new holes for the 20hp transom bracket?
  3. L

    Trolling Motors - Convert Bow Model to Stern

    I have two Minn Kota trolling motors, Both about 50 lbs. thrust. One is a bow model and one is a transom model, whose lower unit is trashed.<br /><br />I no longer have a boat that could use the bow mount. I want to convert the bow mount to stern mount. It would appear that I could use the...
  4. L

    Finding Rivet Leaks

    Going to replace the leaky rivets in my Starcraft. What is the best way to find the problem ones?<br /><br />The boat sits on a roller trailer. Do I just run a hose into the hull until the water comes up to the flooring? Should I use jackstands to reduce weight on the tires and springs?<br /><br...
  5. L

    Volvo Prop?

    My new repower package is in shipment, and is supposed to included everything but the prop.<br /><br />So, I need to find a prop for a new Volvo 4.3GXi/Sx. Probably a 19" pitch.<br /><br />I've been told that my 1987 OMC 4.3 props won't fit due to 15 vs 19 splines. <br /><br />So, what are my...
  6. L

    Engine Compartment Moisture

    My cuddy is kept on a trailer with a fitted canvas cover. There is always some water in the bilge from boating and rain.<br /><br />When the temperature rises, the bilge water condenses and soaks the inside of the plywood/carpeted engine cover. Worse, that moisture forms drops that then drip all...
  7. L

    Repowering - OMC Cobra to Volvo SX

    I have a 1987 Starcraft Islander 221 aluminum cuddy, that meets my needs as being seaworthy, but easy to trailer. Problem is, the 4.3 2-bbl engine is smoking, thumping, and has low compression (<110 on all six). Also, have spent mucho research, time, and $ on the Cobra drive and really don't...
  8. L

    OMC Cobra 4.3 low voltage to Coil

    I have trouble starting my Cobra 4.3. This is an early Cobra with breaker points. When I turn the starter it will only fire at the instant that I release the key after 10 or more cranks. Bad way to have to start it. So it appears that it will "catch" only when the engine is cranking but the...
  9. L

    Marathon Radials on HDG Rims?

    I have been checking various sites to price buying new tires and wheels. I see Goodyear Marathon radials for sale, but always with aluminum or chromed wheels. Never with hot dipped galvanized wheels.<br /><br />Is there some reason for this? Do the Marathons require a very precisely machined...
  10. L

    Replacement axle question

    Thanks for the recent replies on my thread about "Hot Tires". I followed the advice to consider replacing my overloaded single axle with Champion Trailer's tandem conversion.<br /><br />Looks good, and is what I need, but it brought up another question. My current axle is 2X3 inches and fits...
  11. L

    Hot Tires

    Last night, after a one hour trip at highway speeds, I checked my hubs for heat.<br /><br />The hubs were warm, but not excessive; same thing for the lug nuts.<br /><br />But, the outer rim, where the wheel flares out was VERY hot, as were the tires.<br /><br />Am running single-axle trailer...
  12. L

    Re-sizing a Bimini Top

    I have a 6' 3-bow Taylor Bimini top on my Starcraft. The problem is that is the 54" high model, which is simply too high up for my needs.<br /><br />What do I have to consider when planning to cut it down by 12" ? Is there a certain geometry that must be followed to make sure it will still align...
  13. L

    Flag socket angle

    I'm planning on installing a flag pole on the stern of my 22' cuddy. Looks like a 16 X 24 flag is the correct size, maybe with a 30" pole.<br /><br />But, I see ads for both 90 and also 45 degree flag sockets. I like to see a flag flying perpendicular in full breeze, but could use some advice on...
  14. L

    Flushing Salt without a Hose

    Here's my scene: drive two hours to launch my boat into the salt water of the Bay. Come back to ramp at 6:00. Need to flush salt water out of engine, but no water faucets available at ramp.<br /><br />Drive two hours back, plus stop for dinner. Get home after 9:00 in residental cul-de-sac.<br...
  15. L

    Evinrude 40 Propshaft Detente balls

    Last night, I was working on replacing the gears on my 1960 Lark with a new gearset from a 1972 model. Everything looked identical, but I could not move the shift dog. Finally tapped it with a small hammer, and as it moved, some things sprung out of the propshaft and were lost. <br /><br />Found...
  16. L

    Cracked OMC Exhaust Manifold

    Fired up my 1987 4.3 Cobra yesterday and see that I have a small leak in the right exhaust manifold just above the drain. The crack is about an inch wide and level with the floor. The amount of leakage is a small drip.<br /><br />The engine ran fine and the plugs are not clean, as they would be...
  17. L

    1960's Evinrude 40 - sealing Shift Rod

    I recently bought another lower unit for my 1960 Evinrude Lark 40. The seller stated that it was pressure tested. He forgot to mention that the pressure was zero.<br /><br />The pressure is leaking from the mechanical shift rod's passage from the gearcase. This is something I have trouble...
  18. L

    Liqua-Lube ?

    Has anyone had experience with the Liqua-Lube oil bath hub kit (www.liqualube.com)?<br /><br />It's an oil bath like Turbo Lube, but uses your existing hub. Looks like it's been around for a number of years, mostly used by lake fishermen.<br /><br />Any comments?
  19. L

    OMC 4.3 Oil Drain Thread Size

    Bought an electric oil pump to draw the used oil from my engine. The kit included a hose that has a female garden hose fitting, which would screw over the OMC 4.3's threads at the top of the dipstick tube. Great - that would eliminate having to use the long probe drain hose.<br /><br />But, the...
  20. L

    OMC Cobra Water Pump Drain Screw ?

    When getting my 1987 OMC 4.3 ready for winter, I unscrewed a drain plug in the center of the port side of the upper gearcase housing. This seems to drain the water pump area.<br /><br />When I went to replace the screw, I found that there were no threads there, and that it had been glued in...
Top