Search results

  1. Isa4325

    1972 Chrysler Outboard 70 HP 707HE

    Guys I need a little help here. After timing the outboard I noticed that the timing adjustment nylon two piece bracket was complete closed looking like one piece, not the usual 3/8" to 1/2" gap between the two pieces. Timed at 28* advanced telling me something is not right but what? For some...
  2. Isa4325

    1972 Chrysler 707HE 70 HP Timing Issue

    I thought I had already posted this but I must have done something wrong so here I go again. I am having a timing issue and lost the printed answer that Jerry had given me. Is it possible to get that link again due to me not being able to remember what I did before? Thank you.
  3. Isa4325

    Chrysler 707HE 70 HP Outboard

    Ok, been looking for a distributor cap and carbon center tip With no luck. My question is I have a perfectly good distributor cap but the sinner sprung carbon tip that goes to the road or when the Cabazon broke and no longer exist. Is it possible to use a carbon brush for an electric motor and...
  4. Isa4325

    Timing Issues

    I have a 1972 Chrysler 70HP 707HE Outboard that I converted from a electronic ignition to a coil and condenser. My flywheel has a 0* mark and a 36* mark which I see several different timing sets through out the internet. I set my timing at 4* advance by putting my 0* mark at negative 4 on the...
  5. Isa4325

    Bimini Frame

    Is it possible to order a Bimini top frame only. I have a new Bimini Top Boot ordered to fit my boat but I now need a Frame.
  6. Isa4325

    70HP Chrysler 707HE Float Jets

    I am not finding anything on these float jets that give me a size. I have 5 that appear to be complete and one that has nothing in the bottom giving it a size. See photo to see jets for size, please if you would call me on my cell and let me know if there is any help out there, 713-899-3336
  7. Isa4325

    Over heating warning horn

    I put in a new sending unit and ready to test it, orange wire to ground, any input as to how much voltage, ohms, etc I should get? Where do I start looking for a over heating horn for a 1972 Chrysler 70HP 707 HE OUTBOARD?
  8. Isa4325

    Water in Oil?

    Lower end oil looks like it has water in it. What’s up? 1972 Chrysler 70HP 707HE Serial # 3968
  9. Isa4325

    Temperature Sending Unit

    Chrysler 70 HP 707HE Outboard Motor build in 1972 Does the factory temp sending unit only work with the over heating horn? Would it work with a temperature gauge?
  10. Isa4325

    WOT Woes!

    Something is not right. At WOT my engine hit 2000 RPM and settled in with a per. WOT should have hit some where around 5000 + RPM's. Checking timing and the actions called for in my SELCO Chrysler Outboard Repair Manual 1962-1984 required a circumference of my flywheel and then the WOT timing...
  11. Isa4325

    1973 OUACHATA with 1972 Chrysler 70HP 707HE Outboard

    Finished the rebuild of hull and outboard but I can not find a normal operating temp for idle or cruising at 4500 RPM. Checked the sending unit for continuity cold and hot. None at cold and normal when hot but temp gauge doesn't sean to show any operating temp at idle even though the thermostat...
  12. Isa4325

    Gas and Shift Cable Adjustments

    Is there somewhere I can find a method for adjusting Gas and Shift Cables on my Chrysler 70HP 707HE Outboard?
  13. Isa4325

    Thank you all

    Just wanted to than you all for the help I received and wanted to say that iBOAT is the greatest site for the DIY mariner.
  14. Isa4325

    Chrysler 70 HP 707HE Fuel Lines

    Can anyone tell me where these two lines go? The fuel line coming from the top of the fuel bowl has fuel coming out of it if I pump the fuel to the engine. That doesn't make since to me. HELP PLEASE????????
  15. Isa4325

    Chrysler 70 HP 707HE Steering

    Sorry - Not permitted.
  16. Isa4325

    Tillotson Carborators

    I am looking for three carburetor kits for these Tillotson WB8B carburetors (333061-1). Can anyone suggest where to look? Chrysler 70HP 707HE Outboard
  17. Isa4325

    Chrysler 70 HP 707HE

    OK I removed the flywheel and stator from the 3 cylinder 70 HP 707HE engine. OHM the stator to 1.0 to .9 ohms. Cleaned exposed shaft, key and slot, inside flywheel and magnets, stator ring which showed no continuity and charging wires(2) which did show continuity between the two wires. Needs a...
  18. Isa4325

    Chrysler Magnapower 70 ignition woes

    Went for my first start after cleaning and checking the engine out for crank, compression, and plug wire voltages. My first crank with fuel/oil returned a pop and smoke bellowing out from below the flywheel as if from the Stator?????? Voltage to electronic ignition but nothing coming out to...
  19. Isa4325

    Removable or Tilt & Trim

    I want to remove my tilt & trim units completely from the Chrysler 70 Outboard and while reading in my repair manual it say to remove the lower shaft forst before removing the upper shaft holding the unit in place. HOW DO I REMOVE THE LOWER AND OR UPPER SHAFTS? DO I DRIVE THEM OUT FROM ONE SIDE...
  20. Isa4325

    1972 Ouachita Convincer U16 Hull Repairs/ Chrysler 70 207HE rebuilt engine.

    I want to re do the fiberglass work on the kell covering up some of the bare hull showing through. My thought is to use resin, hardener, and fiberglass cloth. painting it white to accent the hull. Any comments or suggestions would be helpful.
Top