Search results

  1. Bgbbgb246

    Force 120 or 125?

    I've purchased 2 force 120hp motors (i think). They were cheap with good compression. They allegedly run but one developed a miss and the previous owners mechanic told him that forces weren't worth investing any money into. So long story short, he re-powered and i bought the motors for a few...
  2. Bgbbgb246

    Mystery part on drive shaft

    While pulling a Powerhead off of a 25 inch midsection to put it on my 20 inch midsection I found the part pictured on the driveshaft between the Powerhead and mid section. Out of my own stupidity, i took it off to inspect it and forgot what direction it was on the drive shaft. I cant find the...
  3. Bgbbgb246

    Fisher sv-19 gt w/ 150EFI prop pitch?

    I have a 1995 Fisher sv 19 gt. Nadaguides claims my boat has a “net weight” of 1100lbs. Its not clear to me whether this includes the motor dry weight or not. originally it had a force 120 on it. This force 120 had an aluminum 19p prop. I decided to get rid of the foce and pick up a very...
  4. Bgbbgb246

    Mercury 2.5 liter interchangeability

    Ive seen variations of this question asked but i cant seem to find a concrete answer. My question pertains to the interchangeability of 2.5 litre mercs from the late 90s and early 2000s. Specifically my scenario is that i have an xr6 150 with a blown powerhead. I havnt had a lot of luck in the...
  5. Bgbbgb246

    wncmarinesalesinc.com

    Quick question for you all. Looking for a used 150hp motor for my bass boat. Havnt had much luck locally at boat shops or on marketplace/craigslist. Havnt seen anything on ebay either. After looking online for a while i did find a used motor that i like on wncmarinesalesinc.com. I cant find...
  6. Bgbbgb246

    External trim/tilt pump

    Hi all, Im looking for a motor for my bass boat and i found a reasonable priced mid 80s mercury 150 for sale. Motor runs great and starts right up. My only concern is that the motor requires an external pump for the trim/tilt. I had a 1995 force 120 that had the internal trim/tilt pump so i...
  7. Bgbbgb246

    gel coat curing

    I did a full gel coat job on an old 80s bass boat. The process was a real pain and took a lot of time but everything went really well. I used FIberglast materials starting with a red base coat, followed that with clear and flake, and then many coats of clear over that. On the last coat i used...
  8. Bgbbgb246

    The differences between a 135 and 150 optimax

    I looked around the web for the differences between the 135 and 150 Optimax as i hard that they were almost the same motor being manufactured out of the same block. There was some good information like the fact that the gearing is different in the lower end (135 is 2:1 and 150 is 1.87:1), they...
  9. Bgbbgb246

    Redistributing weight after repowering

    I recently re-powered my 19-ft Fisher shallow v bass boat with its maximum horsepower of 150 horsepower. On the first test drive I quickly realized that I would have to remove my 10" jack plate as the boat sat very unlevel. (I know the ridiculously big Jack plate to try to use on the maximum...
  10. Bgbbgb246

    Painting an aluminum boat "professionally"

    I have a 19' Fisher aluminum bass boat with faded paint and graphics. I plan to repaint and have the graphics re created to make it look nice again. I've done some research on painting aluminum boats and all I can seem to find is information on painting jon boats with Rust-Oleum. I'd like to...
  11. Bgbbgb246

    Force mounting bolts

    I have a face 120 on a Fisher sv-19 that I am putting a slidemaster jack plate on. During this process I have noticed that that the 1/2" bolts used to mount the engine are a little smaller than the holes in the outboard and the jack plate. As far as I can tell from research, that 1/2-in bolts...
  12. Bgbbgb246

    1995 force 120 fuel check valve?

    I have a 1995 Force 120 and I was replacing all the fuel lines because I've been having a problem keeping the boat primed. Every time I turn off the motor for more than half an hour I have to reprime the motor because the bulb is soft. For good measure I replaced all the fuel lines before the...
  13. Bgbbgb246

    Missing coast guard sticker and I need hp info

    I have a 1995 Fisher sv 19 gt. Its a shallow v bass boat that came with a force 120hp. So heres my problem. I want to repower in the near future and I have no idea what the max hp rating of my boat is because it is missing the coast guard sticker. I have searched the internet for this info in...
Top