Search results

  1. C

    Motor

    I have rebuild my transom on 1996 keener 21 ft CC then I Installed the motor, its not right because the left rear digs deep when I take off and the rooster tail sprays high on the right side. Im going to install a jack plate and bigger motor, I. Going to plug the top holes, how do I...
  2. C

    Motor support racks

    Im needing to build a rach to hold (2) johnson 150 and (1) 200. How wide and how far apart should the wheels be to support these three motors
  3. C

    Motor lift plate

    I bought a c ouple of 96 johnson 200. They are 25 in. My boat is 20 in. I have found lift plates to raise it 5 inches, that are rated for 225. They look like 12 aluminum angle iron. Jas any one ever used them? I have seen manual jack plates, are they necessary?
  4. C

    Lowrance warranty

    Lowrance elite fs 9 i bought the unit and it sat in the box over 3 years. The sonar went blank. I ran troughtrouble shooting with them on the phone for ever. Then they told me to send it in. 40 for testing 440 for a replacement. They send me a newer model brand new. I guess. 5 time on the water...
  5. C

    Rebuilt floor question.

    1996 21 kenner CC I did a total floor stringers and transom rebuild. I drilled holes 24" ft. Apart. Then mixed my foam and poured it in the holes until it expanded out the others. Some times I didn't have enough, so i added more. I assumed it filled the void. I used a level from side to side to...
  6. C

    Transon mounted trolling motor

    I have 21 center console boat. I have an 80 trust on the front with foot control. I want to add a hand sterring clamp style on the transom. Will a 50 lb. Work the slowly move my boat I want an pilot but now is not the time. Im looking for a used one.
  7. C

    Mercury TT

    I dont have the model # I have 99 200 TT. Does it interchange with an 86 TT?
  8. C

    Seastar hydrolic steering testing

    I'm having problems after I hit the motor putting extreme pressure on. I lost my steering. Things done i have bleedit to death many times. I have removed it an totally disassembled it twice, every thing was oily and spotless clean, removed the 4 springs and ball bearing twice. Secondtime I...
  9. C

    Teleflex sterring

    I'm needing a new sterring cable for sh5023 helmet sterring box. My old cable is ss07217. I can't find a replacement for it. Are these cables replaceable? Or do i need to replace everything?
  10. C

    Over revving

    1987 j 48 rebuild cards, fresh gas. It's starting on manual hockey, ideal rough. Sometimes it starts revving like thet when they are running out of fuel. The settles down to rough idea. After 20 minutes of messing With it. It has started revving out of control on its on, I had6to chock it...
  11. C

    Seastar hydraulic

    I have damaged part number 5 on my pump HH5271 build-in lock valve for positive rubber lock. Seastar doesn't sell this part. Does anyone know where I can buy one? Thanks.
  12. C

    Steering setup

    I'm looking to replace the steering system on a 87 johnson 48 hp. Most I look at are Chinese and universal. Will they work on my boat? Where is a good place to one of good quality?
  13. C

    97 mercury 115 hp. Drive shaft removl

    I can't get the drive shaft out the lower unit. Pinion gear nut is off, the crankshaft seal housing is off. In the pictures there something that looks like the back of a seal ive tried to drill a small hole, so I can pull it with a puller. I don't have a manual. This is a one time seal job for...
  14. C

    Johnson PTT colors

    I'm connecting a 96 150 Ignition wire harness a 1990 150. The 90 has 4 wires for TT BLUE, GREEN, RED, AND BROWN. the 96 has BLUE ,GREEN AND A WHITE I only have a manual for the 96. I would think the red would connect with the white with tan stripe for power. What is the brown on the PTT plug...
  15. C

    Lawrence FS 9

    I had a Lawrence elite ti2 I was had problems, it was about 3 years old, I sent it in under a 50% warranty, 220. To fix or 460. To replace it. With a 6 month warranty. They sent me a Lawrence elite fs 9, The problem is the typographical maps Is not very detailed, it's missing a 2 mile...
  16. C

    Acceleration problems

    1996 j150 My boat starts with the flip of the key. She will idle in gear, it's struggles and dies when I accelerate, if I push it slowly. It will run rough but I can to WOT and runs great, then I can back of to 1/4 throttle and still runs great. But if I go back to idle, it's struggles on...
  17. C

    Pulling a boat motor.

    I'm fixing to pull a 90 johnson 150 from a boat to my stand, is it safe to lift the motor using 3. 5/15 bolts in the flywheel? If the is a better way other than buying a i-boat for the crankshaft. If i know the thread type, I could buy a not and build one,
  18. C

    I have a Lawrence 9 ti2, blank white screen.

    I have a 3 year Lawrence ti2. I've only used a fer times, i had a boat rebuild take long than it should have, First problem was a grounding issue, tech support walk my through it. I c an hold the power wire to get a good ground, Not sure if its fixed, Went out the last 2 times, and touch...
  19. C

    AC voltage 1990 evenrude

    I bought a 1990 evenrude 150. I got the motor running, Im checking everything out, Running, I get 9.0 volts ac on ( y1, ) and 2.4 volts ac on( y2 ) Together I get 25 volts ac I have 3 Stater plates to compare against each other for resistance, One on a running motor, one is extra parts and...
  20. C

    Power head swap

    I have a 1996 Johnson 150 , I purchased a 1991 Evinrude xp 150 that runs great. the linkage is the same, I know ill need a cord adapter, my question is, will this power head bolt to my mid section? are the driveshaft splines the same?
Top