Search results

  1. L

    Mid to late 60's wellcraft

    My friend gave me a mid to late Wellcraft 60's runabout: sn: 47(2)489, model # 81500v, With a merc 500 thunderbolt, sn: 2167900. want to do a winter project, but dont know what year the boat or engine. Can anyone help. Floats and engine starts but needs work. Thanks/
  2. L

    Transom Installation

    I have finally removed my old rotten transom and need some advice on installing my new one. I need to know what type of adhesive and how to clamp it into place. I thought of several through bolts to pull it tight, but that is more holes in the transom. Any advice or ideas would be great. My...
  3. L

    minor transom rot

    Is there a filler that I can use for minor transom rot? I have removed bad area and I have heard of some kind of epoxy filler. Any Ideas?
  4. L

    Transom Replacement

    Hey folks, I have a '73 Ouachita 14' and upon removing the motor I notice that the interior of the transom is getting soft. the exterior is solid. The boat is fiberglass. Can I replace the transom or use it till the motor falls off? Or just scrap the boat?
  5. L

    '72 25hp lower unit water

    Just drained my lower unit and the first steady stream was clear water, after that milky oil. Where do i start to track down this problem, or is this a problem. Never have had so much water come out only milky oil in the past. Thanks
  6. L

    Flywheel Key

    Just finished rebuilding carbs cleaned pistons and cyl, new points, condenser and coils. Reassembled everything and tried to start and sheared the key on the shaft that the fly wheel fits on. What did I do wrong and is this key easy to replace or do I need to tear it back down again. Manual is...
  7. L

    Pull Start housing

    Does the pull start housing really need to be mounted on the engine? I have never been able to pull start it and the electric start works fine. I have a '72 25hp rude. It's just an extra step if I'm working on the motor or electrical, and extra parts to keep up with, not a big pain, but does...
  8. L

    IV carb

    What a great group. Been following posts and been a lot of help. My question is, I am rebuilding my carb on a 25hp '72 evinrude. The manual says to back out the low speed needle valve 1 1/4 turns after lightly seated. I took exactly 30 turns to screw it in. Is this a valid spec? I doesn't...
  9. L

    25hp evinrude no start

    I have a 25hp '72. A couple of days ago motor would not start. Pulled the lid off and saw that the screws holding the carb bowl had backed out. Removed the carb and tightened the screws. Tried to start again, still no start. Good compression on both cyl. Good spark. Fuel is pumping. Anyone...
  10. L

    IV carb question

    Tried to start at the lake yesterday, nothing. Pulled the lid off and saw that the screws for the electric choke had backed out and upon removal of the carb, all 4 screws were loose. These 4 screws attach the bowl. Never had this problem before. Can I use a lock washer or some form of lock...
  11. L

    Tach install

    How and where do you hook up a tach and is it possible to mount one permantly on my boat? I have a '72 rude model 25252. The manual says a tach can be installed on any engine but does not say how to do it. Thanks Guys
  12. L

    Fresh fuel

    Hey guys, How long can fuel be stored befor it is not considered fresh. I only get to use my boat maybe every other weekend and have a problem with the engine sputtering when i use the previous outings remaining fuel. When I empty the tank and put "Fresh Fuel" with the 50:1 mix it runs fine...
  13. L

    Cooling problems?

    I have and evenrude 25. Ser# 25252. I notice that on the transom side of the shaft housing that there were two pee holes and were emmiting water. Now that I'm using the boat regulary I noticed that the bottom hole trickels water and the upper hole does nothing. Should I be worried.<br />Thanks
  14. L

    Fly wheel removal

    I have a 25hp evinrude 72 and cannot remove the flywheel. Yes I did remove the nut and have broken 2 removal bolt head trying to remove it. Am I missing something. thanks for the help
  15. L

    1 Hour limit

    Hey good friends, My 25hp evinrude will run at wot for about 1hr and then spit and sputter, then quit. any suggestions. this has happened several times in the past few outings. after it rests a little it fires right up with no problems. Thanks
  16. L

    decarbing

    What is decarbing and how do you do it? Do I need to do it? What will it help if I do it. I have a 25 evinrude 1973.<br />Thanks
  17. L

    Pull start

    As stated in a previous posting I am new to this, so I apologize for mulitple postings. Here is my question, Electric start works fine, but I cannot pull start the motor. I'm a fairly in shape person. The motor is a 25hp evinrude 1972. Is there a technique to doing this or do I need to work out...
  18. L

    Fuel mixture

    First time to this forum and it's great. <br />I recently was given an evinrude 25 model 25252, serial#re03620 (1972?). After a lot of tinkering I got it running and seems to run fine, but it smokes really bad. I added 1 pint of oil to 6 gallons of fuel (50:1?). Do I have the right mixture...
Top