Search results

  1. M

    Surge Brake Actuator - latch went over and is now stuck

    Got an older Atwood surge brake actuator on the boat i just got. Had the ball jammed in and couldn't remove. Took the actuator off and noticed the lever inside that moves the lock forward/back is stuck ABOVE the locking piece aka is moving in wrong direction and doesn't let the lock fully...
  2. M

    Starcraft Superfisherman 196 2000

    Hello! Looking to purchase a boat and just checked a Starcraft Superfisherman 196 2000 at a dealer. 150hp EFI Merc, looked like immaculate condition. Trailer was original, everything clean and shiny. Boat was purchased at same dealership brand new by older gentleman who couldn't fish anymore so...
  3. M

    Bad coupler, warped splines? Alpha one gen 1

    Hello, Old 1991 Glassport with 1989 2.5 ( 120hp ) Mecruiser. Boat started making grinding noise. Took alpha one off, replaced gimbal bearing and ujoints, now can't get it back on. Alignment tool goes in n out smoothly. Took gimbal bearing and shaft off the alpha, it barely engages into couple...
  4. M

    How to put lower unti in fwd? ( Alpha 1 gen 1)

    Had the unit off for gimbal replacement with boat in fwd. However when putting back i noticed spinning prop doesn't move the shaft and kicks the gear piece out. I've tried moving thw small piece that controls gears up/down and turn it. I get it to lock so prop can't move counter clockwise and...
  5. M

    Leave outside with drive off?

    Hello, Was wondering if someone could help me - is it safe to leave boat outside for a week wirh outdrive off? Got a grinding sound on last outing when we got back to dock, same on muffs now. Most likely ujoints or gimbal shot, or both i guess, based off what i read so far. Ordered whole kit...
  6. M

    Mercarb 2bbl - Accelerator pump A and B - interchangeable?

    Hello, I'm having issues with my accelerator pump. Trying to rebuild carb, overlooked pump style when ordering the rebuild kit. My carb has a pump with straight piece and the carb kit came with bent rod aka style B. The straight one seems to be a ***** to find in Canada. The question is, are...
  7. M

    Mercruiser 2.5 Alpha One gen 1 - running without exhaust bellows

    Hello folks! Recently got a 1991 Glassport with Mercruiser 2.5. Tuned and did some work on it in last month, runs flawless. Was about to go fishing tomorrow, got all gear in, kicker mounted etc. Then noticed my exhaust bellow on outdrive side was disconnected and had a little tiny tear on end...
  8. M

    Pressed in hub - remove or find washers?

    Hello, total newbie with props. Got a boat recently with bad prop. Current prop has a Flo Torq II hub kit in it. Found used prop nearby from same stern drive ( alpha one gen 1 ). However new prop seems to have a pressed in hub, see the pic. I've tried removing it to replace with Flo Torq kit...
  9. M

    Alpha One Gen 1 Trim Switch contacts

    Got a boat recently with Alpha One Gen 1. Won't go up from Control up, only down. Moves up from trailer button thought. Won't show trim level on gauge either. Was going to try cleaning contacts and if it doesn't work replace next season. Cleaned inside, but questioning now wether it was put...
  10. M

    Johnson 1970 throttle cable needle doesn't move enough for full throttle

    Hey folks, Could someone help me with throttle cable sync/adjustment? I've got a 1970 Johnson 40hp with electric shift, so a single throttle cable going directly to the remote control. I've no idea what the proper length would be or if it's even possible to get one, but the cable has 1 loop i'd...
  11. M

    Johnson 40ES70A Choke spring position

    Hey folks, Was wondering if someone can help me with the automatic choke on the 1970 40hp engine with hot air choke. I can't figure out what should be position of the choke spring on the starboard side. There's On, Automatic and Off choke positions. The spring was disconnected initally so...
  12. M

    Am i missing a cable? Johnson 1970 40hp

    Looking for some help with the wiring, total noob at it. Got my hands on this motor, cheap deal with a boat and trailer. When i turn the key, solenoid engages but starter doesn't. Checked starter manually, runs and engine started ratatatatata, just needs a good carb cleanup besides detailing...
  13. M

    1970 40hp Carb Removal

    Just got my hands on 1970 40hp electramatic on a 14foot boat. Boat hull is fine, going to clean interior and do some work on it. Tried starting engine today, dies on automatic choke, carb definitely dead, engine stayed for 3 years. Switching to choke off, manually runs it, but doesn't feel...
Top