Search results

  1. M

    93 Johnson 115 did I do link and Sync right? See Video..

    https://www.youtube.com/watch?v=ReeuaVh8uZQ&feature=g-crec If link doesnt work Just youtube, Johnson 1992 115 xflow Link and Sync. Just curious if this looks correct on my my 1993 Johnson 115. Thanks in advance.
  2. M

    93' 115 crossflow oily water 3 little holes

    93' 115 johnson Leaking oily water. First let me say the engine has just had 2 new pistons and new rings all 4 cylinders. Less then 1 hour run time on it. I noticed after putting it back together and running it. oil leaking from the 3 little holes Towards the upper leading edge of the lower...
  3. M

    93' 115 johnson, Exhaust oil in water

    Have a 93' 115 johnson. There is black oily watery substance leaking from were water should be coming out. There are three 1/8" holes one on the back of the lower unit and two on the underside of the cav plate on either side of the lower unit. Also when i say back i mean cone side or bow side of...
  4. M

    93' 115 johnson, ring missing, Update

    Just giving you all an update. Problem started with the engine only reaching 4200 rpm. found a ring had been chewed up by cylinder one. <br />The engine is in the shop now. and the mech found that the ring pin, that keeps the ring from turning was gone. Letting the ring rotate on the piston, and...
  5. M

    115 crossflow 93' johnson, help, piston kit #

    Found cylinder one lost a ring and chewed it up.<br />The cylinder walls still look ok though, may just have to have it honed. I need to know what the kit number is for the piston and rings, for both standard and next oversize piston would be?<br /><br />Also can i mix wesco pistons with OMC...
  6. M

    93' 115 johnson, Piston ring missing

    Hi everyone, My worst fear was been realized. On an earlier post you all said it could be a bad piston. I didnt want to believe ya. My original post was the engine would only turn 4200 rpm @ wot with a 13x19 prop. I did another compression check with a more accurate gauge and found cylinders...
  7. M

    93' 115 johnson, how to set timing out of water

    Need to check the timing to see if it is correct. Need to check it out of the water, due to the fact of the gas prices and living an hour from the lake. I have a timing light ready to go so let me know.
  8. M

    vro pump bulb question. 93' 115 johnson

    The vro bulb is hard all the time. I called johnson before i found this site. to find out the starting procedure, SHE said one pump would do it when starting it up after it set for a while. my question is when should i pump the oil bulb? And is it normal to be hard to pump? Also there are no...
  9. M

    93' 115 johnson black stuff leaking from exhaust?

    Is it normal after running your engine to have black oily like substance come out of the propeller? I dont believe it is lower unit oil. I checked it and it is a different color. also it is not much about a dollar size on the floor.
  10. M

    Johnson '93' 115 timing question?

    I need to set the timing on my 93 v4 90degree 115hp. In my seloc manual, it says to adjust the timing at wot to 28degrees and idle to 3 degrees. It appears that both adjustments are done at the same thumb wheel. my qyestion is can i set idle timing to spec and be fine on my wot timing? The...
  11. M

    Powerpack problem?

    93' 115 johnson 90degree. Changed angine spark plugs and plug wires. Started engine, and was not firing on the top port side cylinder. changed plug wire still not firing. changed ignition pack with another cylinder, then all cylinders started firing. <br />I performed the test in the seloc...
  12. M

    Primer solinoid? Arrow point?

    Wich way should the red arrow point. My manual just says run and prime. but does not indicate wich way it should point. Also it is a 93' johnson 115 90degree v4. Right now it is pointed to the port side.
  13. M

    93' 115 johnson Compression high 280psi

    Have a 93' 115hp outboard 90degree v4 johnson compression reads 280psi all cylinders plus or minus 4psi all cylinders. I have verified the guage with another guage. Boat is a 17 foot nitro. boat does 98 miles an hour, at 5800rpm. The boat reaches this speed in about1 second. I emty a 15 gallon...
  14. M

    13x19 to a 14x19 prop 93' 115 johnson

    I went to the local johnson shop to purchase a new prop. I had a 13x19prop but they only had a 14x19. Asked him if he was positive this would clear the anti-cavitation plate, he said yes it will work just fine on your motor. I put the prop on and it does clear, it clears by abought a little more...
  15. M

    Johnson '93' 115 cylinder missing

    Well yesterday i spent some cash on parts.<br />I bought new prop, spark plugs, plug wires, fuel filter, fuel hose with primer bulb.<br />Installed everything fired her up. and engine had no spark on one cylinder. swaped cables with another clinder still no change. Swaped the Hi voltage pack...
  16. M

    93 johnson 115, Tac reading wrong?

    I have a Nitro 170DC, with a 93 johnson 115 running a 13x19 aluminum prop. The problem is a mechanic told me that somethin is wrong with it.<br />At full throttle and trimmed out(accordind to the trim indicator) The motor is only turning 4200rpm @ about 40mph. He told me that turning that low of...
Top