Search results

  1. H

    Yamaha F300 lower unit

    Anyone have a good source for a remanufactured lower unit on a 2015 Yamaha 300 HP? Thanks in advance
  2. H

    Timing on the 5.7GSI

    I'm trying to set the timing correctly. The Harmonic Balancer only has one mark and there is a V notch on the block. When lined up does this indicate TDC of #1 or where the timing should be set with the timing light? Thanks! ---Mike
  3. H

    Volvo Penta 5.7L Cooling problem

    Last year I replaced my motor with a re-manufactured short block from Jasper but since then I've had a strange cooling problem. When the motor first starts up and warms, it will keep getting hotter and hotter until I put it in neutral and rev the motor, then it will start cooling back down to...
  4. H

    Trade my 1998 Johnson 15hp short shaft for your long shaft?

    Hello, I have a great shape 1998 15hp Johnson short shaft but need a long shaft instead.. anyone want to trade, shafts, motors??
  5. H

    Battery connected backwards on my Volvo Penta 5.7, now electrical issues!

    My friend was helping out, connected a ground to a hot lead and when we turned the battery switch on, it caught fire. We put it out pretty quickly but now I have electrical issues. The Fuel Injectors won't come on, thus the motor will not start. Has this happened to you, do you know what the...
  6. H

    Volvo Penta 5.7GSI-PWTR that just wont start, cranks and cranks

    Hi All, I have a 99 Striper boat with a Hi All, I have a 99 Striper boat with a Volovo Penta 5.7GSI-PWTR that just wont start, cranks and cranks and sometimes tries to start. Compression is 88lbs on the low, 120lbs on the high Spark is there but seems kind of weak. I've replaced the battery...
  7. H

    Sierra pump ok on my Vovlo 5.7 ?

    Hello, Does anyone know if I can use this Sierra Fuel pump (18-7330) on my Volvo Penta 5.7 Gsi? Thanks!
  8. H

    Furuno FCV 582L Always shows bottom at half the scale

    Hello, I bought a used FCV-582L and it seems no matter which scale (Depth) I have it set to, it always shows the bottom at around 40% of the scale I'm on. So if I have it set to the 500' depth, the bottoms shows up around 240', Same thing if I just move the scale to 100', it shows the bottom at...
  9. H

    Oil Pan replacement

    I have a replacement pan, thinking about using a good under coating on it to hopefully reduce corrosion again.. Thoughts? Also want to add a small bilge pump as far back as possible??
  10. H

    Bennet Trim Tab won't bleed

    I got some air in the line of my Starboard trim tab and now I cant get it to bleed out. I've tested it at the motor and fluid comes out when hitting the switch but that trim tab wont fill up with fluid. Any suggestions? HH
  11. H

    Engine Removal

    I need to pull the engine to replace the flywheel, it's a Vovlo Penta 5.7L Gsi, fuel injected.. Any words of wisdom? Special tools needed? Do I need to remove the outdrive? Thanks!
  12. H

    What is this and where does this hose go?

    Hello, I have a Volvo Penta with a 5.7 GSI-PWTR What is this just left of my Distributer cap and at the rear top of the engine? It has fuel lines going to the top, bottom of it has a 1/2" rubber hose This is the other end of that 1/2" hose, where does it go? Thanks! HH
  13. H

    Volvo Penta 5.7L Flywheel

    I have a broken tooth on my flywheel Where would be the best place to get a new one? Are they just a GM part? Thanks! The Motor is a Volvo Penta 5.7 GSI PWTR Thanks! HH
  14. H

    Mysterious elbow on my port riser

    I'm trying to find out if this elbow is suppose to be on my Volvo Penta 5.7. Not internal cooled.. It's on the inside of the port side. The manifolds and risers were replaced but it took 6 weeks for my local shop to get the correct ones so the boat sat for that time with the risers and...
  15. H

    Volvo I/O cutting out at higher rpm's

    Hello, I Have a Striper with a Volvo Penta 5.7L Gsi that started cutting out at higher rpm's (3k+) just a little at first but has gotten worse the last few times out. The higher the rpm's the more it seems to be cutting out now. The boat does not sit for long so the fuel could not have gone...
  16. H

    Volvo DP outdrive replacing bellows

    Hello, I Have a 1999 Volvo Dual Prop (DP-SM, Product# 3868913) Outdrive and need to replace the bellows. Does any one know the basic procedure? It looks like I can just remove the rear part of it at the pivot bolts (14mm 12pt bolts?) as well as removing the linkage and pivot pin from...
  17. H

    Where can I get OEM part numbers for my Force 150

    I was trying to order parts from iboats here but they couldnt help me needed unless I had OEM part numbers??? Anyone know where I can get OEM part numbers for my '92 Force 150? Thanks! --Mike
  18. H

    Force 150 wont idle, dies, spews gas

    Hello, I have a '92 Force 150HP that wont idle, spews gas out of the carburetors and just keeps dying on me. I've taken the carbs apart, cleaned the jets and passages but it still does it. Any ideas? --Mike
  19. H

    Broken throttle cable to my '92 Force 150

    The cable broke near the throttle assembly.. Any one know where I can find a throttle cable for my 92' Force 150? Thanks, Mike jnzy@hotmail.com
  20. H

    Taking a '91 150hp lower unit apart - help!

    So the bearing from the driveshaft has gone out again (last time it cost me $800) and this time I want to try and fix it myself. This causes the oils seal under the water pump to leak. I have caught it quickly, drained the oils and flushed it out so the damage should be minimal. I do have...
Top