Search results

  1. R

    2003 90hp merc,rough idle

    so i have had a rough idle problem,I have rebuild the carbs,fuel pump,replaced the trigger,stator, swapped cdm modules and now I cut the cyl 3 and cyl 2 kill switch wire blk/white and have noticed when I turn the motor off with the switch it stayed running cyl number 1 is still firing? is this...
  2. R

    90 hp 3cly pop then pressure through fuel line

    So I've had a rough idle for a few months, rebuild the carbs,fuel pump, trigger, cdm replaced, flushed tank, replaced cylinder number 3 reed valve comp 125psi through 3 cly. My question is what would cause a pop possible backfire?when this happens there is no fuel coming out of the carbs but...
  3. R

    2003 mer elpo 2 stroke has sa lean bogg off idle ?

    Hello.I have a 2003 90 hp 3cyl merc outboard.I was wondering if there was a procedure for adjusting the carbs.heres what I have .I had to drain the fuel tank and rebuild the carbs due to some water intrusion in the fuel system.the boat sat last year.I have taken it out 3 times the 1st time out...
  4. R

    converting my 94quart seat-ice chest to L-Post

    hi.I have been looking for a frame that lifts my ice chest about a foot and converts it to a leaning post seat>i own a 2003 kenner that came witha 94qt ice chest witha seat cushion,I saw this one kenner that had a 54qt seat? that had a frame that lifted the ice chest about a foot.I have searched...
  5. R

    Can someone direct me to kenner boat parts

    hi I have a 2003 kenner today i hit a low dock and it broke my rear corner cover aluminum,its a kenner part.I looked on the kenner web site but it only shows new boats also need a new storage bin hatch hinges and a a few other boat parts,rubber moldings.is there a web site i can buy these kind...
  6. R

    cannon warraty

    hi I bought 2 mag 10a downriggers and 1 week later one does not go down,man what a bummer,I'm told cannon has a warranty on the electrcal parts,I'm 80 percent positive its the board]circuit] can I send it in?
  7. R

    Help I need some info on mounting downriggers

    Ok,I got me a set of cannon mag 10s electric,I also have 2 easy troll,there mounted on my 03 19ft kenner,I need some ideas as how to mount these,there heavy and have a long boom so the stress will be greater.as it is with my manual d.rigger they seem to strees the sides of my boat.has anyone...
  8. R

    90 hp 3 cyl merc,

    I have a question,does anyone have a certain easy way to remove the piston pins,and all the roller pins.is there is there an easy way to install them other than having all them needle pins fall out,mabye heavy on the vasoline and stick them to the pin then slide the piston in?can I use auto...
  9. R

    Ishop marinie.com

    I hope I can post this question ,I im getting ready to buy 500.00 in parts from ishopmarine,Has anyone used this place and how were they?
  10. R

    90 hp outboard pwerhead questions,

    Can anyone please give me some tips on going though my powerhead.I have a few questions.I would like nothing more than to take it to a shop but I just cannot afford it.so I'm going to attempt to find my problem.[noise] slight knocking noise engine runs great but at idle it has a high pitch...
  11. R

    help I'm gona tear it down

    I'm a ford senoir master tech and have torn down an older 2 stroke merc.my questions this see lower topic stalling 90 hp and knocking well the knocking seem like a piston slap.comp is 130 all .can I have good comp and still have piston noise,I bought some gallon baggies a few small ice chests...
  12. R

    2003 90 hp elpto,2nd post knocking noise

    I posted a thread here one week ago,thanks to all now I have the stalling and oil injection working but theres a noise,-------------------------------------------------------------------------------- well ok I went ahead and marked the oil tank and premixed fuel.then I took it out tuesday...
  13. R

    2003 90 hp outboard stalling carb?

    I have a 2003 90 hp 2 stroke merc outboard my problem stated last week while fishing .I notice boat took longer to start than normal.as I took off about 3000rpm it flat out died.I restarted it using choke and had throttle up half way as it started to throttle up I hit choke a couple of times and...
  14. R

    Downrigger ?

    This may not be the place to post but ill give it a shot.I own 2 cannon easy troll man downriggers. My ? is can I convert them to electric and if so were can i get the motors?
  15. R

    Kenner Boats

    I recently purchased a 18v135 kenner bay boat And am very pleased with the quality and ride of this boat.Are there any other kenner boat owners out there and if so what do you think of kenner boats.
  16. R

    Kenner Boats

    I recently purchased a 18v135 kenner bay boat And am very pleased with the quality and ride of this boat.Are there any other kenner boat owners out there and if so what do you think of kenner boats.
  17. R

    2002 MERC 90 TWO STROKE

    Im planning on buying a kenner bay boat outfitted with the merc 90 hp 2 stroke what do you all thing about this motor? my brother says it idle like crap and will not troll to long.
  18. R

    carb problem?

    I just overhauled my carb on my 80 merc 2 stroke 40 hp.because it would not idle.well now it starts cold fine but afer running it for about 20 mins.then i shut it down and if i let it sit for longer than 15 min.its hard to start.so a choke it a little then it finnaly starts,but theres a fine...
  19. R

    charging marine batts

    Is their any certain way to charge these batteries? i have an auto charger i believe it is a 12 volt 10 amp fast charger. I have 2 marine starting batts, that are fairly new but seem to not hold a charge very well. Am i charging these the wrong way.
  20. R

    Porpoising

    Can someone please explain Porpoising and chine walk I read this alot on this forum and dont have a clear view of this thanks.
Top