Search results

  1. D

    Part I’m looking for.

    Any help on what this part is called. I have looked all over the internet and found nothing. I broke it off removing the rod it’s connected to. 98 Yamaha 200hp. Bottom carb. Any help would be greatly appreciated! Thanks!
  2. D

    96 90HP Evinrude No Reverse, Neutral is in gear after changing Waterpump

    This beast shifted fine until I changed the water-pump. Once I got it back together, I have no reverse and it staying in gear in Neutral. I can see the shift rod moving when I look at it from the side and seems to be trying to shift.
  3. D

    2000 5hp Lower unit removal

    Hello, I'm trying to replace the water pump on my 2000 5hp Mercury. Serial Number: 0D993982 I get the two screws off at the bottom it slides down about 1 inch. and stops! Now here's where the weird part comes in. The shirt rod does go all the way up the back of the motor it stops about half...
  4. D

    96 90HP Evinrude Ocean Pro runs fine then bad

    I'm puzzled and need a bit of help. Below will be the list of things done to this motor already. What it does is is it will kill constantly until it warms up somewhat. Once it does warm up, it runs BEAUTIFUL. Then after running it for a bit it will have a slight miss and try to even kill every...
  5. D

    Here's a dumb question....

    I know this maybe dumb BUT I'm sure other inquiring minds besides mine would like to know. What will the lower unit do on the water if the gear oil is old? Slip? Not get up to speed? run at higher RPM on the Motor? Or just run normal?? Just wanting to know. Johnson J150STLCOS
  6. D

    85 150hp Johnson Shift problem

    We replaced the water pump and water intake screen. Now it will shift into reverse freely and neutral but not forward. It's like it's blocked. Took too much off when we tried to undo the shift shaft from the top. We took off the shift lever with the screw and the pin. Took us a bit to get in...
  7. D

    Replacing Water intake screen

    I'm replacing the water pump and want to replace the intake screens as well (they are broke out). I have the pump off and I'm not seeing anyway of taking out the old screens without taking the drive shaft out. :( I hope I'm wrong. 85 Johnson 150 V6 J150STLCOS
  8. D

    96 90HP Evinrude Ocean Pro uneven temperature

    Just a quick question to confirm what I already think. I took it out and ran it for 5-7 mins and it ran BEAUTIFUL! Then it started to run rough and even killed. I touched the top of the heads after I had it out of the water and the one side seemed a lot hotter than the other. I pulled the...
  9. D

    Rough Running Johnson GT 150

    J150stlcos I'm thinking I'm narrowing it down but I'm going to give this a shot and see how close I am. Fresh fuel in the tank - New Fuel/Water Separator, primer bulb. - Compression test is fine. (on the muffs) I primed the bulb and fired up the motor with No problem. It ran ok but I notice...
  10. D

    Overheat Buzzer

    Probably real simple. I just installed a used '85 VRO 150 Johnson V6. The motor has NOT even been run yet. When I turn the key ON (not to the full starting position but just ON) the Overheat Alarm stays on. I know it's not overheating. I hasn't ran yet. Easy fix?????
  11. D

    Steering real free.

    2000 Suzuki 200hp on a 25' CC. The steering has a TON of play in it and when you go to turn, you have to crank and crank. It's getting freer everyday. Is this a low fluid issue maybe? THANKS in Advance!
  12. D

    Starts and Kills

    Sorry but I'm a noobie to the waters.<br />I have a Chrysler 50HP 2-stroke that purred like a kitten. Then one day it would crank and crank but wouldn't start. I brought it home and got it to start with the hose attachment "muffs" on the motor with water running though it. Purred again! BUT as...
Top