Search results

  1. G

    Enamel Hardener?

    I have read that you can add hardener to enamel paint. What kind is required? The same as for automotive paint or is it special for enamel paint?
  2. G

    Rectifier?

    What is a rectifier and what does it do? ***I apologize if this is a duplicate post, it said this post did not exist after posting it the first time.***
  3. G

    power pack

    What do power packs do and how?
  4. G

    bogs when trying to throttle up

    Hi All, I have a 72 Evinrude 50hp, 50272C. Starts great and runs good upto about a 1/4 throttle. If I give it more it bogs. Interstingly if I hit the electric choke and then release it, the rpms increase and I can throttle up a little for a few seconds. Any ideas? Compression is great...
  5. G

    Can't find an electronic shift controller?

    Hi All, I have been working on this problem a few days and found a solution.... If you don't have the correct control box for your electronic shift motor (in my case a 1972 Evinrude). From the ignition harness there are a green and blue wire. One for reverse and one for forward. Get a...
  6. G

    what prop?

    I have a 1972 50 hp Evinrude (50272C). Anyone know what kind of prop I need?
  7. G

    how to shift gears?

    Before you chuckle, I am still a newbie....I am working on a 1972 Evinrude 50272C, 50 hp, 2 cylinder. Where do you hook up the gear controls???
  8. G

    150 psi good 4 a 1972 evinrude?

    Hi All, I have moved on to a 1972 Evinrude. Wanting to make sure I don't have the same issues...is 150 psi good for the 72' Evinrude? Thanks. BTW, if your looking for a 1967 Johnson, I posted mine on ebay. item numner 120019681564...
  9. G

    Head and valve cover

    Hi, Does anyone know the torch spec for the head and valve cover bolts for a 1967 Johnson Seahorse 60 hp? Thanks ***Yes, I know I need a manual, so if that is your post, dont' waste yours and mine time.***
  10. G

    intermittent idle issue

    Hi All, I have a 1967 Johnson 4 cylinder. I just rebuilt the carb and fuel pump. Some times it idles in gear great, other times it doesn't like to start and idle. It runs good at WOT. Any ideas? Thanks.
  11. G

    1967 Johnson owners - FYI

    Hi, FYI, if you need or want to replace your high speed jets welch plugs and don't know the size...they are 0.74 or 3/4. NAPA has them. Removing them makes it much wasier to properly clean the high speed jets. ***This is for 1967 Johnson 4 cylinder engines.***
  12. G

    welch plug size

    Hi, Does anyone know the size of the welch plugs on a 1967 4 cylinder Johnson carb? I don't have any calipers. Thanks.
  13. G

    high speed needle cleaning

    Hi All, Anyone know of a good way to clean the high speed jets on a 67 Johnson 60 hp? Without taking those two little plugs out... Thanks
  14. G

    coil to "M"

    I have a positive white w/red stripe wire that comes from the coil. Should this be connected to one of the "M" terminals on the ignition switch, or the ACC terminal?
  15. G

    No Muffy...No Start

    Hi All, My 1967 Johnson 4 cylinder, 65 hp, model VXL-13A runs fine in the back yard on a muffy. When I get it in the lake it doesn't want to start. Can someone assist me or do I need to add wheels and a driveline?;) Thanks for your attention. Pete
  16. G

    coil question

    Can I replace my stock coil with an universal 12 volt automotive coil? It should be the same correct? I have a 1967 Johnson 4 cylinder, 60hp. Thanks.
  17. G

    Do you have a 1967 Johnson?

    Hi, If you have a 1967 Johnson 4 banger, please contact me. I need some assistance. Thank you!
  18. G

    ignition wiring help

    Hi, Does anyone know how the ignition wiring goes? Below is the information I have. 1967 Johnson 60 hp. 4 cylynder, electronic ingition, model VXL-13A Thanks!
  19. G

    1967 Johnson WOT issue

    Hi All,<br /><br />Intro: <br />I am new to owning a boat. This is my first boat. I acquired this one from my brother-in-law.<br /><br />Details:<br />1967 Johnson 60 hp. 4 cylynder <br />electronic ingition <br />model VXL-13A <br />Serial Number J2746859<br />90 psi compression<br /><br...
Top