Search results

  1. F

    Cutting pexiglass for windshield

    Does anyone have any tips for cutting pexiglass to minimize risk of cracking it?<br />It's for a boat windshield and will be cutting curves as well as straight lines.<br />Thanks
  2. F

    bending pexiglass for windshield

    Can pexiglass be heated and bent with heat gun to make windshield on speedboat,or or would lexan be a better choice.<br />I've heard you can cold bend lexan,anyone know?<br />thanks.
  3. F

    Merc 110 cooling issues.

    I have a 76 merc 110 9.8 hp.<br />Installed new impeller,when started there's lots of water from the tell tale.<br />Drive for about 10 min. and the water flow gets less & less then stops.<br />Shut the motor off then start up and it does the same thing,lots of flow then stops after about 10...
  4. F

    Restoring springbok boat

    I'm looking for info on old speedboats,lots of info on motors,but is there any for boats?<br />I have a springbok aluminum speedboat and looking for pictures of interior to restore somewhat to original.From early 70's 14 ft.
  5. F

    small hole in aluminum boat

    I'm in the process of repainting my aluminum boat and found a small hole about 1/8 inch in bottom.<br />I guess I found that slow leak I had.<br />Does anyone know what would be the best way to repair this?
  6. F

    restoring boat

    I'm in the process of restoring my aluminum speed boat.<br />when I removed old paint I found original stickers under paint but can only make out 2 or 3 letters of decal and can't make out name.<br />It's an old boat and has had the windshield removed and altered.<br />My question is;<br />Is...
  7. F

    Aluminum boat paint preparation.

    I'm in the process of restoring my 14 ft. aluminum boat.<br />I have the boat down to the bare metal.<br />I was wondering if anyone knows the proper paint procedure for painting aluminum?<br />I.e.priming,sealing,painting?<br />Planning on spraying.<br />thanks.
  8. F

    Not shifting 9.8 h.p.

    I have a 1976 merc 110 9.8 h.p.<br />The shifter moves and clicks into F.N &R but it stays in forward gear,any info on what may be wrong?<br />Shift shaft is turning.
  9. F

    Repair on aluminum boat.

    I have a 14 foot aluminum boat which has small leakage around the seam of the keel,my question is;is there any type of sealant I can put along the seam before I paint the boat that will stick good to aluminum?
  10. F

    What year is motor?

    Evinrude 6 H.P.<br />Ser.# 6602B C480723<br />I'm trying to find out year of this motor,can anyone help?<br />thanks.
  11. F

    Prop removal

    I am trying to change the prop seal on my merc,but I am having trouble removing the prop,seems to be seized on.<br />Any suggestions on how to remove a stuck prop?
  12. F

    Parts for old motor

    I'm looking for a site to find parts for a 35 H.P. merc.1963.<br />Any suggestions?
  13. F

    Electric start

    Merc 350 s/n 1588174.<br />I have a control box with no ignition switch,hoping to hook up electric start.<br />Does anyone know where I can get a wiring diagram to run an ignition switch?
  14. F

    Changing oil in foot

    I have a merc 200,sn 7090383.I am in the process of changing oil in foot.<br />I have drained oil,is the small screw about 6 inch above drain the fill?<br />If it is,what's the easiest way to get oil in.<br />Having a hard time to get oil in.
  15. F

    What year/HP is my evinrude?

    I have an old Evinrude which uses a pressure tank system.<br />I cannot find a tag or ser # on it,is there any place on the motor where I may be able to find some type of number on it to identify it.<br />It's a two cylinder,says fastwin on it.I'm guessing in the 10 h.p. range judging by the...
  16. F

    What year is this motor?

    I am trying to find year & H.P.of this motor.<br />It's a mercury 200,serial # 7090383.<br />Thanks.
  17. F

    Controls

    I have an older 35 hp mercury outboard with electric & manual start.I have no controls with ignition switch & harness.<br />Will this motor work with Quicksilver controls off a 20 hp merc,with no ignition switch?<br />Is it possible to run an ignition switch from the dash and battery cables to...
  18. F

    Controls

    [No message]
Top