Search results

  1. L

    2003 mecruiser 5.7 mpi riser reinstall

    Looking for tourge ft / pounds for riser bolts. risers are dry joint. seloc manual says 84 ft pounds seems high to me. thanks
  2. L

    merc 470 170hp

    Looking for some help mercruiser 470 water in oil manifold and riser seem to be ok what is next to look for? thanks
  3. L

    boat seats

    redoing my boat interia Rampage 24. does anyone know where the makers of back cove and like boats (higher end) get there interias. everything online is so cookie cutter. also looking for a good looking swim plat form. thanks
  4. L

    hull repair

    putting boat on trailer this year i put a goo size gouge in the bottom of hull what material is the best to fill with and proceduer.
  5. L

    bravo one removal

    just bought boat with a bravo one outdrive. When removing outdrive doese the drive have to be in forward position to remove out drive. thanks
  6. L

    reman carbs

    loking for reasonly priced and dependable place to purchase a rodchester q-jet 4b. there are alot of places on line. thanks
  7. L

    timing procedure

    just anouther timing question.<br />merc 260 5.7 thunderbolt 1V <br />what is proper procedure to time . i cannot get timing to 8* i keep reading about grounding wires. what wires am i supposed to ground in order to get base timing? complete tune up was done at start of spring. also cannot get...
  8. L

    idle and timming

    1990 260hp 5.7 mercruiser.<br />having trouble with idle and timming engine idleing around 1000 rpm cant get below 950 or so. also cant get timming at 8 degrees its at about 14 advanced right now what am i doing wrong and what should i be looking for.<br />thanks
  9. L

    luhrs 250 tournament

    starting to look into luhrs 250 turnament doese anyone no a place where i can get some information and good pictures of these boats<br />thanks
  10. L

    quadra jet merc 5.7 260hp

    getting ready to launch boat after long spring of nickles and dimes. complete tune up boat will not idle bleow 1000 rpm. it has a quadra jet 4 brl. what should i be looking for also there is a quadra jet expert at my local napa if i need a rebuild what are the differences in auto to marine...
  11. L

    shift cable / cut out swith mechanism explanation

    merch 260 alpha one 1990:could someone explain how the cut out mechanism works . the cut out switch doese not seem to be piveting what action causes it to pivot or to rock the cut out swithch switch works when move by hand. when reading on this site it sates that the switch works in reverse not...
  12. L

    bellows caught in the moment

    merc.260 alpha one. Installed new bellows this weekend went great*&%^$(.when bellows were installed looked at friend and relized didnt put glue on all ends of bellows. from the pros. will i be ok without glue, clamp is on the way it should be.or should i go threw the pain again.
  13. L

    bell housing

    alpha one: changing all bellows and gimble bearing this weekend does the bell housing have to come apart to install bellows? any other tricks and or things i should look for and do while im in the middle of replaceing.<br />thanks
  14. L

    bellows and gimbal

    looking for transon rebuild kit has anyone ever used After Market Marine online for parts? any problems with after market parts ?
  15. L

    gimbal bearing

    long time reader, first post<br />it was sunday, getting ready to install out drive<br />(alpha 260 merc)stuck hand in bellows to inspect gimbal bearing. IT DID NOT TURN. it was brand new last year. as i think back there was some oil in bellows when i took it off for winter. freind said it was...
Top