Search results

  1. C

    Any Ideas

    You guys helped yesterday. I have a new question about my motor! It is a 2000,200, Johnson. I went to lake today, and it took for ever to start. Then smoked like a smoke stack! Then when put in gear died! Then finally was able to get it to run a little, Not on plane about 1200 to 1300. Give It...
  2. C

    Lever

    I know that there is an device on side of my motor that is used to help when fogging and starting. I forgot what it is called. I have a Johnson 200, 2000 model, Carb! I know that you turn it one way for fogging and then another to run if I remember correct. I have not used boat in several yrs...
  3. C

    Aquiring Map

    I have a LMS250C, that I bought a couple of years ago. I've installed the update! My problem is, I turn it on and it shows downtown Tulsa OK. That is where it is made or was! I live in Coweta, OK. Outside of Tulsa. I can not get it to show my location. I just tried it for the first time...
  4. C

    Gas springs

    This should be simple! But I want to make sure I do it right! I'm adding two gas springs, with hardware to,two storage compartments. The don't have any at this time. I made sure the brackets I bought would clear and work. I used the same size spring (I call them shocks) that is used on my main...
  5. C

    Paint on unit

    I have a 200 Johnson, Model# J200PLSSC. I have had paint peel off the lower unit ever since I've owned it! How to fix ? Johnson said they wouldn't do it! Out of warranty. That was 7 to 8 yrs ago. It is just getting worse !!!! I Appreciate any Help or Response... Thank You Davey C Sr
  6. C

    Control lever

    I have a 2000 19SS Stratos. I'm trying to get the control arm off !!! I have to remove panel behind it to replace it! I have already taken handle lock and power tilt button off. The rest is giving me fits. I know there are three screws to main housing have them loose. Arm is locked on some how...
  7. C

    Skin?

    I assume that is what they call them! The ones you see on some pro boats!! I'm looking for a dealer here in US,in Ok if possible. I don't want to cover my hull .I want to try and cover dash panels ! What do you guys and gals think? It would never fade... Thanks for any help... David C Sr
  8. C

    Transducer

    I'm sure it has been talked or asked about! But I'm replacing my old LMS and new unit has different transducer. Old one is glued on the hull inside the boat. Near front of pad. Would it be a good idea to remove it and install new one in its place, or just mount on transom? I appreciate the help...
  9. C

    Live well Pump Out

    Hey!I hope this is right location. If not let me know! I have a 2000 19 SS Extreme. I have a pump in, recirculate, empty, and aeration. Port and Starboard. I would like to put in a pump out, for the live wells. How hard, would this be? And what parts to buy? Thank You David c Sr.
  10. C

    Glue

    What is best glue or sealer, to use to put a transducer in? For through the hull, mounted inside boat. Thank You David C Sr.
  11. C

    sealent

    What is a good, or best sealer to use on holes that are drilled into boat transom. Also a good or best adhesive to glue with? Thank You David Crockett Sr.
  12. C

    Where to place a skimmer transducer?

    I have a 2000 19SS extreme,that has a through hull transducer. Quits working, no signal return, when I run 55MPH and higher. I know this is air under the boat. I purchased a new GPS/Fish Finder,and it has a skimmer transducer. I just would like to find out excatly where I should place it? My...
  13. C

    Want feed back on LMS-520C choices of maps

    I'm going to buy a LMS-520C tomorrow, or Sunday. It comes with one of the three, following: Mapcard Fishing Hot Spots? PRO or LakeMaster? ProMaps mapcard, or NauticPath. My question is what maps are best??? I'm a bass fisherman in OK. So I know NauticPath is out. What about the others. Which...
  14. C

    What's it called

    I call them struts! Other people call them gas assisted piston shocks. They hold open deck lids on my bass boats.What is their correct name? Thanks David C Sr.
  15. C

    Fuel water separator

    I purchased a fuel water separator from bass pro. It's made by merc. or rather for them. My question is this. I want to purchase a filter with a clear bowl and drain built in. Can any one tell me what filters would fit this unit? Fram, etc.,etc,. Thanks David C Sr.
  16. C

    Need Ideas

    I went to lake today to fish. Motor started and ran fine. Good or decent hole shot. Ran a mile or two. Fished , then sarted motor ran fine. Went to another hole and fished! Started and tried to take off fell flat on face. Restart and did same thing. Tried several times, same results. Finally got...
  17. C

    Perko Latchs/Locks

    Perko Latchs/Locks -------------------------------------------------------------------------------- I've had almost all of my Perko T-handle flush mount Lock/Latchs .Go bad this year. It's the lock breaking. I removed it (lock) and have been trying to get, just the locks. No Luck!!!! I was...
  18. C

    Perko Latchs/Locks

    I've had almost all of my Perko T-handle flush mount Lock/Latchs .Go bad this year. It's the lock breaking. I removed it (lock) and have been trying to get, just the locks. No Luck!!!! I was hopeing some one here may help. I called Perko and talked to a Rep.They promised to get back to me! But...
  19. C

    Water Pressure Question?

    I installed a whole new water pump on my motor this year. A 200HP 2000 Johnson carb. It was a complete kit from Iboats. Made sure pump and all was right. Yesterday was fishing I noticed at idle it was about 12lbs, WOT it went to 32lbs. Isn't this a little high? I also replace T stats and by pass...
  20. C

    Swing away and Lights

    Is there a kit, to make a trailer a swing away tounge?I know the basics of what has to be done, just want to know if kit is made? It is a Stratos trailer.With surge brakes. Also Ideas to give more back up light! For those dark ramps... Thank You
Top