Search results

  1. martyh

    Tilt / Trim pump help

    I am looking for a little help from the Mercruiser experts. I am working on a 1972 Searay 240 with twin GM 165 straight six?s and the serial numbers on the outdrives and engines are long gone. The project I am working on is both tilt/trim motors are dead. They are a single solenoid per pump...
  2. martyh

    Black water tank hoses

    I am trying to clean up the mess and the mickey mouse stuff in the engine compartment from the previous owners lack of skills or knowledge and the black water hoses are in the way. It occurred to me that using a PVC type pipe would make it so much easier to work around. Does anybody know the...
  3. martyh

    Gelcoat repair?

    Hey gang, This is probably a simply answer for most but, I don't have any gelcoat repair experience. I was changing out the seawater valve and inlet strainer and I noticed that the gelcoat is chipped away under the strainer showing the fiberglass. What is the best way to repair it before I put...
  4. martyh

    Yamaha 130 no spark??

    I am working on a 92 Yami 130 V4. It was a runner before I swapped out power heads because of a dead hole (broken piston) and now I have a no spark condition. I have the factory service manual and have done the tests for resistance on the pulser coil and charge coil as described. The pulser...
  5. martyh

    OMC Cobra specialty tools

    Hoping some of the shop guys will chime in. I?m looking for the specialty tools for working on the OMC Cobra drives. Tried E-bay and the other normal places but nothing yet. Any other ideas or places?
  6. martyh

    Wide beam trailers?

    Just have a quick question. For the guys/gals that regularly tow wide beam boats. Where did you find your trailers at? Are they custom made and are they as wide as the beam of the boat? I have a friend that is looking at a 30ftr with an 11?6? beam but it does not come with a trailer and, he is...
  7. martyh

    Trailer measurement questions?

    Hey guys, I just picked up a 24? boat and currently it's sitting on a home made triple axle trailer. It's in real bad shape and I am looking to replace it not repair it. I am going to look at a galvanized roller tandem axle trailer but the owner does not know how long of a boat was on it...
  8. martyh

    Boat rescuing??

    Hey guys, I was hoping for some advice, information and opinions on a boat I am looking at. I am looking at a 1979 Sea Ray 24? with a flybridge. The owner has had it since the early 80?s and spent the majority of there weekends fishing the waters in Alaska. They relocated to Washington in the...
  9. martyh

    Saved an old Sea Ray from the saw....

    My brother talked me into dragging home a 1972 Sea Ray SRV 240 Weekender for him yesturday. The story is, I placed an add online looking for an older Sea Ray boat with a flybridge to resurrect. I got a response from a guy that had a Weekender. He was trying to figure out what to do with it as...
  10. martyh

    Mercruiser outdrives

    I went to look at an old (mid 70?s) Sea Ray 24? weekender for my brother today. It is ford powered (probably 302) and based on the transome bracket (it was still there) it had the mercruiser outdrive. My question is this, with the outdrive, gimble assembly and engine bell housing missing, what...
  11. martyh

    What else, while the O/D is off?

    My outdrive started making a growling noise about 20 yards from the dock today. Took it back home and tore into it. Found bad gimble bearing. The boot is good and the u-joints look and feel good. What else should I look for or replace while I am in there? 1998 Volvo Penta 3.0 Cobra SX drive
  12. martyh

    Alternator wiring?

    Hey guys, I was hoping you could help me with something. I am trying to finish up my basket case 1998 Seaswirl with the carbureted 3.0 Volvo Penta and I have run into a wiring issue. In my haste to pull the old engine while working outside, in the dark, and before it started raining I did not...
  13. martyh

    4.3 heat issue

    Hey guys, I want to bounce something off of you and see what you think. I have a 1988 OMC Cobra with the 4.3. I have had it a few years now and it has always seemed to run hot or at least hot to me, I don?t get to use it very often so I chase problems on it when I have some free time. The temp...
  14. martyh

    Another shift cable question

    I was wondering if somebody could shed some light on shifter cables and a good place to get them. I sent pictures over to the Volvo Penta store through iboats and the reply was they could not help me. I have read related posts but have not found what I am looking for. I?m working on a 1998...
  15. martyh

    Transom seal replacement

    I bought a 98 Seaswirl with a dead 3.0. I have removed the engine to rebuild and the outdrive needed to be removed to be put back together. (shop didn?t put it back together correctly) I was wondering if I should remove the transom mounting brackets to replace the seal/s involved. The boat does...
  16. martyh

    Another dead 3.0

    Hey gang, I just brought home a 1998 17? Seaswirl tonight with a dead Volvo Penta 3.0 4cylinder. The prior owner did not winterize it and when they went to start it in the spring water poured into the bilge and mixed with the oil. I plan to pull the engine tomorrow night to look for the...
  17. martyh

    Merc 4.5

    Hey Gang, my brother purchased a 12? boat over the weekend and it has, what appears to be a 1975 Mercury 4.5hp (#4111184) on it. Not knowing anything about the Merc?s, I got it started and it makes a clicking noise while idling in neutral and I don?t see it peeing water from anywhere. It was...
  18. martyh

    Gamefisher/Force

    I am looking at a 1988 Gamefisher/force outboard. I have not been able to talk to the owner yet about the specific parts that were used, but he claims that it originally started out as a 7.5hp and was upgraded to a 15hp. Is this possible, are the engine pieces that closely related?
  19. martyh

    Evinrude 15hp questions

    Hey guys, I was wondering if you could help me with something. I am new to the outboard area and I am looking at a ’88 15hp Evinrude for my 12’ Gamefisher. It is a short shaft with electric start and a charge cord. The owner says the prop has a few nicks in it but other than that it is in real...
  20. martyh

    Another Sea King 7.5

    I have a Montgomery Wards Sea King 7.5hp The tag says “Clinton Engines Corp.” Model number is K750 3112E Serial number 1140988 Type is XTV 52276 Can anybody direct me to a site that will have information about this motor? I thought I had found information some time ago that it was an early...
Top