Search results

  1. H

    Cone clutch??

    Hello, I have an 88’ Bayliner Trophy with a 5.0 GM, OMC out drive. I want to order a bellows kit. I see some are for and for not a cone clutch.... how do I know which I have?
  2. H

    Running spare hot wires....

    Question, I need to fish a transducer lead through the hull from the dash.... can I run spare hot wires along with it..... meaning, if I tape the wires to the lead, will power going through the spares make any sort of field around the transducer lead, making it inefficient or the like?? thanks
  3. H

    Prop replacement spacer question

    Got a new prop off eBay, same part number as the one I took off. not sure if this new one is a pinch different construction on the hub, but when I slide it one, it seems to bottom out before the spline clears the hub, which does not let me slide that brass splined spacer onto the splines. So...
  4. H

    1988 GM 5L, spark plugs too tight to get out....

    Hello all, while recently doing a tune up, I wanted to replace the plugs.... well, the first on I go to ( starboard side front) is tight as hell.... to the point I didn’t want to torque any more. I didn’t try any other one. Is there a trick of the trade ? * tried on a completely cold engine
  5. H

    Oil capacity?? 1988 GM 5L

    Hello, what it the engine oil capacity of an ‘88 gm 5L, with and without filter change? thanks!
  6. H

    1988 GM OMC 5L points gap???

    Hello all, I have all the stuff to do ignition tune up.... what is the gap for the points? thanks
  7. H

    Oil filter??

    What oil filter does an ‘88 gm 5l use? Fram PH30 or equivalent?
  8. H

    OMC Bayliner Trophy ignition q’s

    Hello all, I just acquired a 1988 trophy with the 5L GM engine.. Previous owner stated the coil needs a hot wire jumped to it to start, and I confirmed this as well. I checked voltage at the switch (3 wire). One is the hot feed, one gets hot on the first click, one is the hot to the starter (I...
  9. H

    Johnson RDE-19m 35 hpp

    Hello, just picked up a 50’s rde-19m Johnson for $40 off a neighbor on Middle Bass island, Ohio. has been sitting for 30 years +\-. I know there are certain steps to take to “awake” this old girl. But, my question is...... this is set up as either an electric start or pull start. Do I need...
  10. H

    J15REEA 15hp Carb Question

    Hi all, My dad called from Fl yesterday to have me do a little parts search and troubleshooting for his J15REEA 15 HP. He was out fishing and it started to act a little strange, was able to make it back but noticed there was a few parts broke. In the parts pic, the roller #3 and vent #29. I...
  11. H

    what is better?

    what is the best way to run house batteries? i have a 39' gulfstar trawler. it has a battery to start the engine, a battery to start the genny, but what is the best configuration for house set-up......run two big 12vdc in parallel.....or four 6vdc in series/parallel.....or is it simply a...
  12. H

    Mkast are you out there????

    Hey, Can you get me a copy of the Volvo AQ80 manuals???? contact me at hoytheld@yahoo.com thanks Jason
  13. H

    ***WANTED*** SHOP/REPAIR MANUAL

    I need a repair/shop manual for a 1962 Volvo 4 cyl engine and stern drive unit. Either need a used one to buy or a location to buy a new one. Thanks Jason
  14. H

    Do one of you dudes want a Winter Project???

    Well...like I have explained before...I like to do all of the stuff on a project....but some of the things I can do better than others...such as the case with the wood wedge I just had Tiller make...yea...I could have done it...got the tools...but I don't like to do that sort of thing...not my...
  15. H

    Outboard stand I whipped up yesterday

    Made from 2" x 3/16" wall stainless. You can just see the recessed 2" stainless wheels at the bottom. The engine clamps onto a block of wood also.
  16. H

    BEEF...have a question

    Beef I need your email addy...have a question about your henry Thanks jason
  17. H

    Is there a WOODWORKER in the house??????????

    I need something made for my henry project. When i removed the rub rail today...there is a "wedge" behind it to keep the rail square as the bow laps curve toward the nose....you can see it in this pic...it is the triangle shaped "wedge" I need a new one made...the angle is 70 degrees and the...
  18. H

    1961 Henry (Skiff Craft) Restoration Follow Along

    Well, I am going to start this thread...and it will be ongoing until spring of next year. I am sure some have seen my posts before on this sweet hunk of firewood I picked up from ebay for $130.00. I am going to do a restoration follow along thread...so when you see this thread surface to the...
  19. H

    CHEAP BOTTOM PAINT???

    yea...I know ...you get what you pay for....but I don't want to sink a mint in bottom paint...is there anything that is cheap???? going on a wood hull..over existing, preped paint.....the boat cost me $130.00...don't want to spend $100 a gal for paint!!
  20. H

    It's Alive!!!!!!!!!

    ...the 40 HP Evinrude Lark III I got on a boat from ebay came to life. I decided to pull apart the wireing harness at the control box...where the silly-noid and junk is...checked for spark and it had spark...so..I hooked up my jumper box direct to the starter...sprayed some starting fluid...and...
Top