Search results

  1. D

    Suzuki DT30 1984 Water in the lower cylinder

    I have a DT 30hp 1984 Suzuki and I'm getting water in the bottom cylinder. I have 100 and 110 pounds of compression (dry) in the cylinders. I had the head milled and a new head gasket installed. All too no avail. No cracks are visible in the head or the block. The head was checked by the machine...
  2. D

    1971 Evin 4HP runs better with cover off

    What causes my motor to run better with the cover off? I put the cover on and attempted to get a smooth running motor but I didn't have any luck. I adjusted the top mixture screw and there was some difference but not as good as when the cover was off. Thanks
  3. D

    What year is my 4hp Evinrude and no spark

    The numbers on the freeze out plug are 4106D and E02946. Also there is no spark in the bottom cylinder.
  4. D

    Suzuki DT 30hp Approximate year 1987 quits

    The engine runs fine but after running around with 3 guys onboard it just dies. I punp the bulb and it starts up and will run great until it dies again after motoring in the bay for 10 or 20 minutes. Any suggestions?
  5. D

    1985 Johnson 140 TXCO wiring diagram

    Both small connectors on my starter relay have a 12 volt reading. My Seloc manual only gives the engine wiring diagram to the large red connector. Could someone help me with the rest of the schmatic which would be from the red plug forward or the entire schmatic from another source. Thanks...
  6. D

    1967 Johnson 3hp - thermostat location

    I recently acquired a 1967 3hp Johnson and it is overheating. I plan on replacing the impeller and the t-stat. Could someone please tell me where the t-stat is located. Thanks
  7. D

    Difficulty steering my 140 hp Johnson

    I haven't used my boat for over a month and when got to use the boat today it was a bear to turn the steering wheel. The cable has a red plastic shield from the rotary connection (inside the cuddy) to the telescoping rod under the powerhead. It looks like I have plenty of grease on the...
  8. D

    What year Johnson/Evinrude 3HP ?

    I have a 3 HP Johnson but the number stamped on the Welch plug says something different. The number is E2813479. Thanks
  9. D

    Installing the lower unit on a 1985 J140TXCO.

    I'm installing the lower unit on my 1985 140 hp with an extra long shaft (25"). I'm confused with the length of the shift rod and the direction of the off set in the shift rod. What should the length be from the flat surface on the L/U to the center of the hole at the top of the shift rod? Also...
  10. D

    What year Force and most common cause for overheating

    Please tell me the year of my Force and what is the most common cause of this motor to overheat? Thanks 9.9hp OE 090571
  11. D

    1985 Johnson 140hp Lower unit special tool for snap rings

    Where can I get a snap ring plier to remove the two internal snap rings that are behind the bearing carrier in the lower unit? Or has someone devised a removal tool a to extract these rings? 1985 140 hp J140TXCO. Thanks
  12. D

    Another question for rickdb1boat E15RLCNC

    I'm having a problem with the info you sent me on my E15RLCNC. You sent me a referance chart to check the ohms on the powerpack and the stator. Thank you.Unfortunately the chart doesn't match the colored wires on my power pack. I'm hoping that you will be able to tell me what the readings should...
  13. D

    15 HP Evinrude E15RLCNC with no spark

    Hi, I have no spark to either plug. I disconnected one leg of the kill switch and I still have no spark. I would like to use an ohm meter to check the coils, powerpack and stator but I do not know what the values should be at the various wires. Can someone please help with what the value should...
Top