Search results

  1. wil7483

    Stuck prop

    I have been in the process of replacing my gimbal bearing, oil seal, shift cable, and u-joints due to the previous bearing becoming frozen to the yoke and causing me major headaches. I have finally gotten everything replaced and back together and today I decided to remove the prop to grease the...
  2. wil7483

    Gimbal Bearing & grease seal installation

    I am ready to start putting this thing back together and want to be sure that I do it completely right. The grease seal is installed with which side facing the engine? Also, the gimbal bearing is installed with the side with the two notches facing in towards the engine right? I have the manual...
  3. wil7483

    Gimbal Bearing grease seal

    What is the correct way to install the seal? Seems like some sort of adhesive is needed to prevent it from falling off as you are driving the bearing into place.
  4. wil7483

    Sticky situation PT III

    I have been working on my gimbal bearing for the past few weeks. For an idea of what's going on you can go here and here. Today after a lot of persuasion I was able to get the inner race of the old gimbal bearing out of the housing. From what I can see the housing wasn't damaged any by the...
  5. wil7483

    Sticky situation PT II

    I decided to start a new post concerning my problem but you can go here and see what I am dealing with. I got the gimbal housing apart so that I can get a closer look at things. Can anyone take a look at the pictures and tell me if they can see any damage that the bearing possibly did. I...
  6. wil7483

    Sticky situation

    I took my boat (1988 Wellcraft Elite 222, Mercruiser 5.7, Alpha One) out yesterday for the 1st time this season and had to be towed in. Got on plane and after a few minutes started smelling what seemed like plastic burning. Everything sounded fine but the smell got stronger so I shifted into...
  7. wil7483

    Lash adjustment ?'s

    Well today I went outside and started from the beginning in an attempt to correct a very noisy lifter (in my opinion). I took the advise from others here on the forum and got an old valve cover and cut an opening in it to be able to adjust the rocker arms with the engine running. I started on...
  8. wil7483

    Planning a 10 - 15 mile gulf trip.

    Hey, I am thinking of planning a 10-15 mile trip out into the gulf for some bottom fishing. I have a 1988 Wellcraft elite which I regularly take out in the bay for 30 mile trips to the various bridges crossing the bay. There are a few wrecks that I want to fish for grouper, snapper, bee-liners...
  9. wil7483

    Carb not opening at WOT?????

    OK, I need your help. I'm not a mechanic and I don't fully understand the workings of the internal combustion engine but I am mechanically inclined so I'll try anything once. I went out today to try to adjust my rocker arms to rid the engine of what I thought was lifter noise. After I completed...
  10. wil7483

    Anyone ever had this happen?

    I was out today changing out the gear lube in the stern drive and once I was finished I noticed that my zinc anode was gone. It was there when I put the drive back on the boat. Why would someone steal that. It is such an inexpensive part. Now I definitely will be putting a prop lock on.
  11. wil7483

    Oil pressure question

    Hey guys, what is the normal oil pressure reading range on a SBC 350 5.7 engine. I is a Rapido Marine rebuilt engine. Under way the pressure is steady at about 40 psi but at idle it is near the 60 psi range. is this normal? I know that the crankcase isn't over full because i just changed the oil...
  12. wil7483

    Thrust Washer Question

    I seem to have lost the thrust washer off of my stern drive. Can someone give me the correct part number to help me find a new replacement one. It is an Alpha One drive approximately 1984 circa.
  13. wil7483

    Rapido 5.7 Break In Prop Question

    Hey. I have a post in the Mercruiser Sterndrive forum about my new Rapido 5.7 SBC I just put in my Wellcraft Elite 222 XL. I took her out today to the ocean and put her thru the paces and wanted to get some opinions. Previously I had a 15p prop on it but I never did a wot run so I don't have any...
  14. wil7483

    Brakes Locked on Trailer

    Hey. Last week I was towing boat to lake and car cut me off and when I slammed on brakes the trailers driver side surge brake locked up. I was able to get it back to my sisters house but it is still locked. In reverse it spins freely but in forward in drags until the speed increases then it...
  15. wil7483

    Sway control bars

    Hey, can anyone tell me anything on how sway control bars work and what kind I need for a dual axle trailer with surge brakes. The boat weighs in at about 4400 lbs empty plus the trailer. I really haven't experienced much sway but on a few occasions during a 170 mile trip I did and it was a...
  16. wil7483

    5.0 to 5.7 Rapido rebuilt engine swap

    I finally decided to go ahead and permenantly pull the weak SBC 305 out of my 1988 Wellcraft and replace it with a rebuilt unit from Rapido-Marine. I spent the better part of last year trying to diagnos and fix all the issues that I was having with the engine and just decided that this year I...
  17. wil7483

    Side panel replacement options

    Hey guys. I am considering replacing the side panels on my boat and was wondering what options I had instead of recovering the new wood with vinyl again. I really want something different and more water resistant. As you can see here the panel is comprised of two seperate pieces of vinyl...
  18. wil7483

    Best Trailer choice and length

    I was going to try to paint my current trailer until I could get a galvanized or aluminum one but have since decided to bite the bullet and just spend the money. My question is should I replace the current trailer with what I currently have (roller trailer) or get one with bunks? Is one better...
  19. wil7483

    Alpha One Question

    I took my outdrive off today to start a trouble shooting session on my low power issues. I put it on a stand, placed it in forward, turned the prop, counted the rotations of the yoke, 1:1.50 which is correct for my engine. The question is, while turning the prop should it turn with no...
  20. wil7483

    Can I have my trailer sandblasted and repainted

    Hey guys, I have a 23' steel trailer that is showing lots of rust. It came with the boat i restored. I do fish 50/50 in salt and freshwater. I know the salt is going to eat the trailer up but I was wondering if I sandblasted it and repainted it professionally could it provide a degree of...
Top