Search results

  1. J

    Mercury 7.5 3450274 shift rod E clip missing.

    From what I can see the shift rod bushing sits on the E clip to prevent the shaft from pulling out. It would be necessary to remove the bushing to replace the E clip. Would like to remove the bushing without damage. I dont have any special tools. Any suggestions.
  2. J

    2001 70HP Johnson 2 Stroke.

    This motor went into SLOW after a short run. The LED and horn system does not work on the boat. The VRO was leaking and therefore suspect. Changed the VRO for the standard fuel pump and running 50:1. Temperatures are good. The motor now runs for a much shorter time before the SLOW kicks in...
  3. J

    2002 ELPTEFI OT 551129.

    This motor has been running well enough all these years. According to the owner it has suffered with fuel in the oil even from new. I have heard of other similar model Mercury motors having the same issue. Mercury told the owner that this is normal. I doubt this is correct. Does anyone have any...
  4. J

    Tohatsu M30 A2 ignition parts availability and compatibility.

    Have an old motor that has recently stopped running, just died. Compressions show 105 and 115. Sparks are strong but notice that they miss every once in a while. Carb is new. Shooting fuel into the carb throat resulted in one loud pop but nothing more. Suspect trigger or CD unit. Cannot find...
  5. J

    2002 60HP EFI fuel pressure regulator question.

    Motor would not start. The VST and fuel pump all gummed up. Everything clean now and the HP pump is running again.. Is it possible that the pressure regulator is also gummed up?
  6. J

    2002 Merc 60HP fuel injected.

    What is the Schrader valve for on the vapor separator. Will this tell me if the HP pump is working.
  7. J

    2002 merc 60ELPTEFI. Not starting.

    Good sparks. Lift pump working , no volts at the high pressure pump connector. should I look for a fuse, a relay or is this the ECM. Dont have a manual for this. Thanks. Jim.
  8. J

    Yamaha S130TXR8.1996 Identification.

    This motor recently purchased by a neighbor was supposedly rebuilt recently. I am not familiar with this model. I have a suspicion that the powerhead came from a different model. Is there an identification on the block similar to what we have on Johnyrudes. The oiling has been removed and the...
  9. J

    J115PL4SR Fuel issue.

    This 2004 4Stroke motor appears in good condition. Will fire and run if fuel sprayed into intake. Fuel will shoot out of low pressure pump. Have replaced the low pressure filter. Can hear the high pressure pump but only a small amount of fuel comes out of it to the injectors. Not easy to get at...
  10. J

    90TLRB oiling rate setting

    Recently acquired and looking for an oil leak at the bottom of the tank, noticed that the lock nut on the oil pump linkage is loose and backed right out, The threads on the rod are exposed a good 1/2 inch. How much of the thread should be showing to ensure good lubrication. Does anyone know the...
  11. J

    Compressions for the following two.

    Can anyone provide me with the good compression numbers for a 2012 Yamaha FX HO and a 2013 Kawasaki STX 15F. I am looking to purchase one or the other. Thanks. Jim.
  12. J

    1977 25HP Evinrude cutting out.

    Starts easily and runs for a short time in idle or at higher revs then "pflut" and stops. Restarts without any changes and does the same thing. Carb has been cleaned and rebuilt. Compressions at or near 120. New plugs. Sparks jump a good size gap using tester. Tried fuel pump by squeezing primer...
  13. J

    Never come across this situation.

    I have what appears to be a V4 lower unit. Measurements say it will fit. However the drive shaft is cut for a woodruff key. I need an impeller and can only find the plastic lobe type or the metal round type. Help please!
  14. J

    Gasket sealant.

    I used to use OMC sealant until it got too expensive then I switched to Perfect Seal. I see now that Perfect Seal is not available. Can you tell me the replacement? Thanks.
  15. J

    2000 150 john 60* shuts down on take off.

    Comps all good. Idles great and revs in the barrel. Idles on load but shuts down on take off. Sparks good with new coil bank and power pack. I believe this smacks of a fuel shortage problem. Checked the fuel filter at the assembly,all clean. Fuel gushes out when prime bulb squeezed. New prime...
  16. J

    Ok I surrender. 2007 9.9 merc 4St

    I only need the resistances and volt outputs for the trigger, stator and power pack. If I can't have that can anyone tell me where I can find a reasonably priced shop manual. Thanks.
  17. J

    1986 110 Johnson.

    Need the re circulation hose routing. I have the 1987 OMC manaul but the routing is not clear. Thanks.
  18. J

    1988 40Hp Evinrude. Not seen before.

    I have the carb's down for cleaning and see that the main pick up tubes, 4 holes on opposite sides, have split along the line of the holes on both carb's. Does this present a problem.
  19. J

    2007 9.9 Tohatsu/Mercury. No sparks.

    Thought this was a Suzuki but I am told that it is a Tohatsu. Tried the Mercury Forum with no result. Perhaps this forum will work. I need the resistance numbers for the Coil, Stator coil and the trigger coil. Can anyone help. Thanks.
  20. J

    2007 Mercury 9.9 4st Pull start.

    This motor stopped running and would not restart. Checked and there is no spark on either cylinder. Can anyone provide me with the test procedure for the coil unit, the CD charge coil and the position sensor. I have a test meter and a D-A converter. I do suspect the power pack. Many thanks in...
Top