Search results

  1. C

    Terrova quit working.

    I purchased a used terrova trolling motor this weekend. I installed it, tested it on the trailer and it worked fine. Got on the water and nothing. Got back home checked the connections and getting power at the plug. The battery tester on the trolling motor shows a full charge. Any ideas on what...
  2. C

    Accessory plug Evinrude

    Looks like the accessory plug has been rewired with all black wires. I cant find a wiring diagram that shows which wire is which. I think the top one is the tach, bottom left is ground and bottom right is power? Anyone know for sure? Thanks.
  3. C

    Muffs on a 79 evinrude?

    Anyone know if muffs will work on a 79 115 evinrude?
  4. C

    84 60hp evinrude cooling problems.

    New impeller in August of last year. Good stream at idle. About 3000rpm stream weakens and almost stops if I go any higher. Alarm will go off If i run it above 3000rpm. Any ideas. Thanks
  5. C

    Newer Carbs on a 79 115

    I just picked up a 79 115 evinrude. Is it worth it to put a newer set of carbs on it to get easier starting? If so, what year carbs would fit? Direct bolt on replacement or are other modification involved?
  6. C

    84' 60hP evinrude Running @ 1/2 rpm

    I have had my boat about about 10 time this season and it has ran great. Smooth idle. Very easy to start. Last night returning to the dock the motor bogged down to 2500 rpm. I ran it for about 10 minutes like this back to the dock. I cut the motor a few times and still would not run past 2500...
  7. C

    How long should tilt hold motor up?

    I have an 84 Evinrued 60hp with tilt and trim. I had to replace a few hoses but seems to be working well. I have noticed if i leave the motor tilted up a little,the next day the motor will be all the way down. Is this normal? I have checked for leaks and cant find any. Manual bypass not tight...
  8. C

    Gas tank question

    I have a 24 pontoon and looking to put a larger tank on it. How far away can I place the tank? I would like to put it in the middle of the boat about 10ft from motor. (1984 60 hp evinrude). Too far? Thanks
  9. C

    84 Evinrude 60 hp gauge questions

    I have recently aquired a 84 60hp Evinrude and would like to add a temp gauge and water pressure gauge. There is an empty bolt hole just above and to the right of the upper sparkplug. Is this were the sender screws into or is this missing a bracket? If this is the hole for temp sender where do i...
  10. C

    84' 60hp evinrude tilt/trim wiring

    I have just bought a 84' 60 hp evinrude with t/t. The wiring has been cut. It has three wires out of the unit and a fourth black wire that runs from the other side. Looking at a wiring diagram im guessing the three wires go to switch. Where does the fourth wire go? Does the t/t get power from...
  11. C

    84' 30 HP prop yamaha

    When i recieved the motor it did not have a prop on it. I have purchased a prop and the repair shop sold me a spacer that goes on before the prop. I have two questions. It is a very tight fit. I havent gotten all the way on. I didnt want to force it. Is it usually difficult to put on? I am...
  12. C

    703 contol

    Ive recently aquired a small boat with a 84 30hp yamaha. The motor is running fine and starts right up. Im not sure if it is wired correctly though. The plug coming from the 703 control box (1 green, 1 yellow, 1 black) the green wire is wired directly to the positvie on the battery. Looking at...
Top