Search results

  1. T

    Suzuki 2013 DF60A

    Purchased a boat with a 2013 Suzuki DF60 on it and trying to locate an owners manual. Suzuki website does not have it available, they only offer the service manual for $80. Really don't need that just want to understand the warning system, how to read proper oil level, etc. Anyone know where to...
  2. T

    2013 Encore Bently Pontoon

    I have the opportunity to purchase a 2013 Bentley 200 Cruise pontoon at a good price. This would be a second boat, just looking to have extra room for friends who always come down to the lake. Our main boat is a Mastercraft that we surf and wake board behind. Not worried about lack of speed...
  3. T

    1992 Johnson 60hp Running Issues

    I have a 92 Johnson 60hp, J60TLENE, that has been running great. Yesterday went out to fish and motor started up fine, idled great, but once put in gear and revved past 1400 RPM it would die. Would rev up fine in Neutral, and run in gear under 1400RPM. Tried pumping the bulb while running and...
  4. T

    Carb adjustment question

    I have a 1992 Johnson 60hp, j60tlene. When setting the mixture screws (on the top left hand of each carb, when facing the engine) I read to set them at 1 1/2 turns out. It seemed that were much further out to begin with, 2 1/2 to 3 1/2. So I adjusted them all to 1 1/2 and fired it up on with...
  5. T

    92 Johnson 60HP Ignition Problems

    So I posted a couple of days ago, see below. Still have the stumble/rough idle, like it is missing. It runs smooth above 1200 rpm, #3 Cylinder plug is oily, checked coils and they are all spec. Compression is #1 140, #2 138 and #3 130 (cold did not test warm). These all seem to be within 10%...
  6. T

    1992 Johnson 60HP, spark issue

    1992 Johnson 60hp, VRO disconnected (mix the fuel) Went to the lake today, motor would not start. Ran great the last 3 days. Getting fuel but had no spark on all 3 cylinders. Switched batteries (new deep cycle for trolling, so good battery) just to be certain that was not the issue. Still no...
  7. T

    Lubricate the throttle cable

    1992 Johnson 60hp, stupid question, but how do you lubricate the throttle cable and with what, seems to be sticky. Steering cable has grease zerts so that one is easy. Thanks
  8. T

    Quick Question on Johnson Outboard

    I am needing to get the carb kits for a 1992 60hp engine, the parts diagram shows early model carbs and late model carbs. Not sure which my eninge has, both diagram carb explosions look the same. My model number is J60TLENE and serial number is G 03165118. Any help would be greatly...
  9. T

    92 Johnson 60hp, starting issues

    A little confused, I have a 92 Johnson 60hp, that I used everyday until 2 months ago. It was running great a couple of months ago. Today, I pull it out to start and clean it up. It would stumble and die. So I drained the carbs, same thing. Pulled carbs, just to check, #1 carb jet was plugged a...
  10. T

    Fuel Deck Fill Question

    I have a bass boat, with a built in fuel tank with a flip open deck fill opening. It turns out this is not waterproof when closed. I had to drain the fuel tank last week, due to water and engine not running. Put a fuel/water separator on it, refilled tank, everything was good. Took out...
  11. T

    1992 Johnson 60hp

    Quick question, I was on Johnson parts page and I noticed that this motor, model # J60TLENE, shows to have a VRO Pump/Tank. Mine does not and I am not the original owner, so this could have been removed. Does anyone know if this was an optional feature on these motors? Thanks, TEX
  12. T

    Livewell Aerator Pump not moving water

    My boat has 2 livewells, one livewell has an aerator that should fill and aerate the water. The aerator comes on but will not fill the livewell when in the water. I can force feed it with a hose out of the water and it works fine. Any ideas on what is wrong? Thanks
  13. T

    Prop Question

    I have a 1992 Johnson 60hp, 3 Cylinder on a 16' Cajun Bass Boat, turning a 14X17 prop. I top out at 35mph at 5100rpm. I noticed that this engine came from the factory with a 12 or 13 3/4" diameter prop. Would I gain much speed from a smaller diameter prop with a different pitch. Am I correct...
  14. T

    Question Regarding Bass Boat

    I bought a 1993 Cajun Bass Boat, and since they are no longer manufactured I can't find any boat docs to answer my question. On the dash there is a push/pull switch labeled fuel. This boat has a 1992 Johnson 60hp with built in fuel tank. Now the boat will run no matter which position the...
  15. T

    Suzuki Question

    Been running Evinrudes for a long time and am now considering a boat with a 1991 DT150, I believe it is the super six with dual spark plugs per cylinder. What do you think about this particular motor? This one is in good shape and has been well taken care of. What is the main difference...
  16. T

    Question regarding water output

    Got a quick question, Chyrsler 1976 45hp, how much water should come out of the tell-tale. Should it be a thick, steady stream or a thin/slow stream. New to this make of outboard. Thanks
  17. T

    New to Chrysler, Have Questions

    I just acquired a 1976 45hp Chrysler outboard and have some questions. What type of lower unit lube do I need to use? Where do you all recommend I by parts from? Any other advice regarding this motor? I am not too familar with Chrysler outboards, I have been running Evinrudes. Do these hold...
  18. T

    1976 45hp

    Just got a new to me 1976 45hp Chrysler and had a couple of questions. Motor runs good, but want to put new impeller, change lu gear oil and plugs. Are these things easy to find parts for and any online dealers you can suggest? What type of gear lube do you all recommend? Any other...
  19. T

    Stripped Lower Unit Drain Screw

    1972 Envinrude 50hp, hydro-electric shift. Rebuilt the lower unit and noticed the drain screw hole was stripped. The screw with the nylon washer would not grab the threads, but without the washer it would tighten down. For a temporary fix I put an o-ring on the screw and it is tight. Anyone...
  20. T

    Question on resealing lower unit

    1972 Evinrude Hydro electric shift, 50hp. I am currently resealing the lower unit and am having trouble figuring out how to replace the housing assembly oil retainer. It looks as if the bearing is pressed in and the oil seal sits behind it. But looking at the schematics in the manual, it...
Top