Search results

  1. B

    Question for the guru's

    I have a 1993 Fountain sportfish with twin 2.5/200hp mercury's. it has 21 pitch 3 blade laser prop's and tops out at 50 mph at 6000 rpm. My question is this seems kinda slow to me? The fountain website says the boat should run 65 with 225's? compression on the motor's is 125psi across the board...
  2. B

    HELP PLEASE manual release valve

    I have a 1993 200hp mercury with the three ram tilt and trim system. last time out the motor got stuck in the up position. while drilling out the manual release valve (seized), I messed up the threads a little. I got a new release valve and it will only screw in a turn or so. is there a tap to...
  3. B

    Snook?

    I have nice big snook swimming in front of my dock but can't get them to bite anything (usually at night). What do they usually go for? Thanks,
  4. B

    anyone seen this before?

    I bought a used outdrive (alpha one). I am putting a new impeller in it and changing out some seals. I have never seen the copper tube on top of the impeller housing in any drawings. looks like it is supposed to be there. help please.
  5. B

    engine controls

    I have a set of "zero effort" controls I would like to use on my searay. does morse make an adapter for mercruiser cables? Thanks, Brian.
  6. B

    Prop slip

    What is the accepted % of slip for a prop? when I plug my numbers into prop calculator's it shows about 30% slip.
  7. B

    84 searay/350 vortec mercruiser

    Ok, I finally got a timing light and set my timing to 8* btdc per specs. But lost 300 rpm's on top end. I had set it by ear originally and I guess i had it a little more advanced. does this mean my distributer is not advance properly? Thanks for any suggestions.
  8. B

    Steering arm pin on alpha 1

    My steering arm pin has slop in it where it connects to the top of the gimbal ring. so I bought a good used one off ebay. I need to know the best way to change it out, and if the outdrive has to come off to do it. Thanks, Brian.
  9. B

    Vortec intake bolts

    Do you guys know where to get the special mounting bolts for a vortec intake manifold? They are supposed to be rounded on the bottom to prevent over-torqueing the intake.:confused:
  10. B

    260hp mercruiser???

    Ok I have decided to re-power my searay. I have a couple quick questions,1. should the new thermostat be a 160* or a 142* I have seen both in mercruisers before? 2.Which exhaust manifolds are better against saltwater corrosion GLM (aluminum) or OSCO (cast iron)? Thanks guys, Brian.
  11. B

    84 searay/260hp mercruiser

    The last time I had this boat out it ran fine, but when I got back to the dock it idled a little rough. pulled the arrestor off the carb and noticed it steaming from the valve cover vent tubes. so what do you guys think head gasket? doesnt show any water in the oil yet?
  12. B

    5.7 merc starter

    I have an 84 Searay that came with a 5.7 mercruiser that has been upgraded to a 1996 5.7 vortec. the old starter was a 4 post solenoid, the new starter is a 3 post solenoid I have the big red wires and solid orange wire connected to the big post. the yellow/red wire to small post on the...
  13. B

    1964 evinrude 9.5 hp

    This engine was completely gone through 2 years ago. Tried to use it this year it fires right up with choke pulled out. As soon as choke is pushed in it dies. I took top half of carb off and cleaned. put it back on and it does the same thing. so far I have replaced fuel lines, cleaned fuel...
Top