Search results

  1. L

    power trim on 93 looper 120

    1993 Evinrude 120 looper 89 Larson Senza Closed Bow my power trim unit is rough or shaky when trimming down in forward gear. does this mean i am due for a trim unit rebuild?
  2. L

    1993 Evinrude 120 bogs @ tilt down

    Engine: 1993 Evinrude 120hp with a 18p Raker I keep my boat on a lake that requires frequent tilt up and tilt down. When tilting the motor from up to down the engine chugs / bogs / runs rough for about 30 seconds before it clears out. if i were to hammer it, the engine is slow to respond and...
  3. L

    Oil Furnace Ignition

    The good ole oil furnace in my garage would not fire up last night! it would pump oil but not fire, pressed the reset button a bunch of times, turned the furnace on/off ect... any advice on troubleshooting / doing cleaning on a oil furnace - thanks
  4. L

    Put your Boat in You WILL!

    Doreen's husband Matt died suddenly one day. Doreen was taking care of the funeral arrangements with the undertaker when she was asked how she wanted Matt's obituary to read. Doreen asked the undertaker, "How much does an obituary cost?" The undertaker replied, "One dollar per word." Doreen...
  5. L

    Starter Skipping

    had a small problemo the other day at the lake, went to start the engine 1993 rude 120 looper and the starter would not engage. she would spin up and go ping and not catch.. it finally caught and the motor ran peeerrrfect... started worked just fine after that as well.. what would cause this to...
  6. L

    looper rev limeter

    my question stems from this. I am running a 93 looper 120 on a 16.2 foot 1050lb larson senza, has a 18p SS raker 13.5, 13 spline 2.1 gear ratio. ( i think its a 2.1 gear ratio, unless there is a 1.86 or 1.78 with a 13 spline. ) I am running 47mph @ WOT, according a prop calculator I should be...
  7. L

    Ignorant Boaters & Wakes

    There is new post about this every day on here so i'd thought i'd add my experience from last night. It was a nice calm night out, water like glass and not too many boats on the lake, as the g/f and I were coming back from a evening of fishing I slowed down at the start of the channel that...
  8. L

    Trailer Lights?

    Ok here's my problem, my lights don't work, no signal or break lights, but all running lights work .. (ie when i turn the lights truck light on the all glow, but still no break or siginal) anyone have any advice to fixing this problem or diagrams thanks alot
  9. L

    What Gas to Use?????

    1993 Rude 120 Looper What gas should i be using in this engine. I have been running 93 octane shell v-power premium. is this the best fuel for the engine or should i be using regular or mid-grade? The engine runs peerrrr-fect on the 93octane
  10. L

    what does spun a hub mean

    i am hearing this over and over, " i spun a hub on my prop today" what does this mean, what is happened to spin a hub?
  11. L

    AIR VENT V4 Looper

    The handle / air vent on the back of my 93 rude 120 opens up like a latch, I would like to open it up to allow air flow. is this recommended? will it help cool or be beneficial in any way to the engine or would it be detrimental? anyone do this to their engine?
  12. L

    Gear Ratio

    whats the gear ratio in a 93 rude 120 looper model =elets
  13. L

    Bought a prop have a Question

    I bought a Raker prop, but it does not say raker on it? do all raker props have raker imbedded or printed on them?
  14. L

    Changing Gear Case Oil?

    I am looking at changing the gear case oil in my 1993 rude 120. I was wondering what steps need to be taken to carry out this procedure properly? what parts need replacing and what is the recommended gear case oil to use? high performance that is. Also how do you know when it is time to...
  15. L

    Transom Height + OB GAP

    just a quick question, i lifted my engine up to set the cav plate approx 2 inch's above the bottom of the hull. now that the motor is lifted i have a gap between the transom plate and the motor "hanger" is this ok, or do i need to get a "wedge" so to speak.
  16. L

    Primer Ball lose of pressure

    When priming the ball on my 1993 rude 120, the ball will get hard and then a couple sqeezes later it will go soft again? what would cause this?
  17. L

    Raker Prop 18 pitch

    I have done some prop testing with 2 props recently aluminum 13.5 19 pitch 5200 rpm @ WOT aluminum 13.5 17 pitch 5600 rpm @ WOT i decided to buy a raker 18 pitch, i figure it will put me @ around 5500 rpm @ WOT. think this was the right purchase?
  18. L

    Hit a Log-Amal

    Last night i hit a log-amal with my 120 rude with a 17 pitch aluminum prop, I was cruising down the river at about 30mph, I saw the log or big stick and throttled back but it was to late, it slid under the hull and proceeded towards the prop. I herd two thumps.... thump ..... thump... i...
  19. L

    Tow Boat with Sunfire

    nhbnb
  20. L

    pop tightness

    so i changed my prop last night, on my 1993 rude 120. my question is, should i just hand tighten the nut and slip the pin through ie the nut will be loose? or do i grab a socket and crank her a little more to get to the tight setting and then slide the pin through. when i took the other...
Top