Search results

  1. B

    Surge brakes to Electric over Hydraulic

    I have not been on the forum for a while. I bought a 2014 Toyota Tundra a few years ago and it has done great pulling the boat. We have been keeping it in a slip the past 4 years. This year we are taking a break from the marina and going on the trailer again. Now that I am going from 10 miles a...
  2. B

    SeaDek is a no go. Input on second choice

    I have a Monterey 250cr and every year I add some type of upgrade to keep it fresh and modern. This year my first choice was to add SeaDek to my swim platform and my cockpit. I chose SeaDek because I like the softness between my feet, the ease of installation, and maybe a little sound...
  3. B

    Online repair manual VP 5.7? Where?

    Bad day for me to be switching to decaf coffee. I remember seeing a link for free online repair manuals that Don put up. After spending an hour searching for that link I am at a loss. Anyone have it in their favorites? 2008 VP 5.7 GI-F . Thank you... Time to go get a real cup of coffee. :)
  4. B

    CDL needed?

    My wife and I are looking at a 28' 5th wheel toy hauler with a GVWR of 12 thousand pounds. My 09 F250 with 6.4 diesel is the tow vehicle. My truck is rated with no issues there but what about my driver license. There will be times where we will be very close to the 12 k. Will I need a CDL A...
  5. B

    What can cause engine coupler failure?

    VP 5.7 light vibration at lower RPM when turning port or starboard. When trimming the light vibration will go away. I thought it was the gamble bearing and u joints in my DP out drive. When the dealer pulled the drive he informed me that the coupler between the motor and out drive is toast...
  6. B

    HELP!! Manifold gasket removal

    07 VP 5.7L tring to clean old gasket off engine block. What I have tried: Very light paint scraper. Didn't work. Next a die cast 1 inch scraper. Would hardly leave a mark on it. Next I bought gasket dissolver from CRC and let that work for a few hours. Didn't touch it. Tried gasoline. Didn't...
  7. B

    Riser bolt question.

    I was told by the dealer that the bolts come with the risers.( Not true) I am scrambling around to get bolts and can only find galvanized 3/8in x 8in long 16 tread. I am concerned that I will get a false torque because of the galvanized coating. Stainless steel I can order but will take 2 weeks...
  8. B

    What are your storage fees for winter?

    I just payed $780.00 for the season. Indoors and heated at 55 degrees. It is a deal from the marina where I slip Sam I Am. I am 27' long 8.5' beam, and will be stored on the trailer. 1st day in is November 1 and have to be out by the end of April. I am also allowed to do work on my boat while in...
  9. B

    1st time Manifolds and Risers on 5.7 What tips?

    I am changing out my manifolds and risers on my VP 5.7 2006 for the first time. My mechanical skill is a 5/10. I have good access to both sides of the motor. The marina who does my work wanted $1300.00 parts and $650.00 labor. Money seems high but they always do a good job. Looking closely at...
  10. B

    Volvo 5.7 Gi-f what spare parts to carry?

    What am I missing? I have raw water impeller with seal, serpentine belt, cap, rotor, fuel/water separator, oil filter, thermostat and gasket (fesh water cooled), barbed plastic tubes of various diameter with clams for any hose break, rubber gloves, oil, ATF, power stealing flued, 1gallon of...
  11. B

    Time for new manifolds and risers.. Please help

    I have a 2007 VP 5.7 GIF. Motor has 390 hours and mostly salt water use. The motor has a heat exchanger but the manifolds and risers are not part of that loop. The motor is flushed with fresh water after every time it is used. I have not flushed with salt away. This spring after my second run I...
  12. B

    From surge to electric help

    I have a Ventura twin axle trailer rated at 9k pounds. I have disk brakes up front and free roller hubs in back. I am considering putting in electric brakes and ditching the surge system I currently have. I have looked for information to help with the decision but have come up short so I need...
  13. B

    From Spindle Zerks to BB back to Spindle Zerks

    Last spring I went to my local trailer guy and bought new races, inner and outer bearings, and 4 rear seals to redo my trailer. While I was there the guy was saying how the BB were far superior to the spindle zerk that feeds grease in just before the rear main seal. I asked a few questions and...
  14. B

    Just took my boats temp

    Outside this morning it was 22 degrees. I keep 2 thermometers in the boat. One probe is in the engine room and the other is down below in the cabin. Engine room is 42 degrees and cabin is 50. My little heaters seem to be doing there jobs. ( Yes they are the explosion proof kind). Even if you...
  15. B

    What type of life jackets do you carry?

    I had some cash burning a hole in my pocket and needed to spend it on the boat. In West Marine I picked up 4 more inflatable life jackets bringing me up to eight...
  16. B

    What are your winter up-grades?

    My 07 Monterey 250cr is getting a 12v TV. I know where I am mounting the TV but I don't have an arch for the antenna. I am thinking it will go on the front rail some where. Not sure if I need a power antenna or not. I am wanting to put in an inverter so I can run the microwave and make a pot of...
  17. B

    Is it time for Risers and manifolds? 5.7GI

    5.7L GI with fresh water cooling. I am at 300 hours and just finished her 4th season of 75% salt and 25% fresh. No sighns of leaks. Just wondering what is a time frame. Also wondering ball park price for risers and manifolds. Thanks
  18. B

    Looking to add TV and DVD to Monterey. Questions.

    My Monterey 250CR is in need of a TV and DVD player. Once football season starts it is hard to get the wife out on the water because the world will come to an end if she doesn't watch pre-game and the games live. DVR at home isn't good enough. Yes, sounds like I need to add a TV and since I am...
  19. B

    Rear Seal Spindal Question

    I am replaceing my hubs and the rear seal area of the Spindal has tiny little black pit marks. I have taken emory cloth and spent an hour rubbing it. The makes are still there but it is smooth. Should that be ok?
  20. B

    New Hubs being returned

    I bought new 6 lug 5.5" 3k pound hubs from my local trailer guy. I opened the box today to pack them with grease so I can finish the trailer tomorrow. Both hubs the back races were not pressed all the way in. On further inspection you can see tremendous heat was used and blue marks on the races...
Top