Search results

  1. B

    Rude 50 hp trim needed

    if anyone has a used complete power trim unit for a 1984 Evinrude 50 hp 4-sale, please email me. Thanks, Bob<br />bmurray@jcn1.com
  2. B

    seats/chairs needed

    My friend is in need of some captain type chairs or seats for his 79 Checkmate. He needs some seats for a swivel seatup in some form of grey, charcoal, black, ect. Please email me if anyone has some used seats that would possible work. Brand not important, just some color combo above. thanks, Bob
  3. B

    steering too tight help

    My double cable rack & pinion steering cables are too tight and make it hard to turn. I need to lube them. Who makes the attachment to lube them with pressurized oil? where can I get it? thanks
  4. B

    compression on my 85 Johnson 150hp low???

    well finally did the compression check on my 85 150 crossflow, and found it quite low. It was about 65-70 psi on all cylinders (didn't do test with throttle open). Now I will do the decarb. I don't think it has ever been done, and should be after every 50 hrs. I don't think this is going to...
  5. B

    85 Johnson 150 problem

    I posted last summer about this intermittant problem I had this last year. When I throttle up (nail it) from take off, or idles down and dies, or it just stays at the same rpm/speed and then all of a sudden it kicks in and launches. Sometimes while cruising it feels like it just shuts down then...
  6. B

    Dhadley, modify intake info???

    you mentioned earlier about modifying my intake on my 85 Johnny 150. Connect left to right? How far down do I mill? Should I use a roughing mill or a finish. Not sure if it should be smooth or not. Please email me or fax any ideas you have on this, Thanks Bob<br /><br />bmurray@jcn1.com<br />fax...
  7. B

    outboard maint info

    here is some good info at his site on outboard maintenence<br /><br /> http://www.overboardboating.com/
  8. B

    OMC airbox mods ???

    I had an engine builder mention to me about some airbox mods for improved performance. I have an 85 Johnson 150 crossflow. I'm in the process of polishing and porting an intake and reed blocks for my engine. Has anyone heard of this and if so what or how is this done? If anyone has any ideas on...
  9. B

    OMC airbox mods???

    I had an engine builder mention to me about some airbox mods for improved performance. I have an 85 Johnson 150 crossflow. I'm in the process of polishing and porting an intake and reed blocks for my engine. Has anyone heard of this and if so what or how is this done? If anyone has any ideas on...
  10. B

    set-up update

    Dhadley. I'm still looking at doing those mods real soon. Here is some info on my prop differences. As I told you my Power Tech 14.25"x23p only turns 4700-4800 rpm's. I put my SST 14.25x21p on and I can turn it 5700-5800. The SST really blows out at the slightest turn and not any faster speeds...
  11. B

    thermostat question

    Dhadley, you mentioned in a past post of mine about the thermostat and my water pressure gauge. Well I'm going to put new t-stats in with these new heads, and I wanted you to clear up something about modifying them for better flow? Thanks
  12. B

    Dhadley or Joe (OMC heads)

    Dhadley or Joe, just got my OMC crossflow heads in. What is the difference from these 79 Johnson 235hp heads and my 85 Johnson 150hp heads. They are supposed to be a higher compression head, but what makes them higher? Is it the dome? These are the ones that I will be machining down and...
  13. B

    looking for porting info

    where do I find some literature on 2-stroke porting-tuning, like "how to" info? Just somewhere to read the basics would be fine. Thanks
  14. B

    water leaking???

    on my 85 Johnson 150, should water be coming from the lower pivot point? This is right behind the plates on the lower mid section. I saw this when hooked to the muffs. I know I have the drain holes on the lower unit and the pee hole on the lower crowling, but what about this. Is this the main...
  15. B

    new setup update (85 Johnson 150 crossflow)

    Dhadley and all. Here is where I'm at with my Charger.<br /><br />Boyesen reeds- MUCH smoother idle, and throttle response.<br /><br />CMC jack plate- Think I need to come up more. even though I'm as much as 3" higher than without. see below on prop.<br /><br />Power Tech prop- 14.25x23...
  16. B

    85 Johnson 150 heads wanted

    If anyone has a blown engine or is parting out one, and wants to sell the heads please email me. Thanks<br /><br />bmurray@jcn1.com ;)
  17. B

    water pressure gauge question

    Just installed a new OMC water pressure gauge. It is Tee'd in with the pee hole. Should I have it setup with the pee hole shooting water or blocked. I can't see how I will ever get a good reading on the gauge as long as it has an open hose to shoot the water. Thanks :)
  18. B

    Jack plate installation update

    Well I finally got the CMC manual jack plate mounted. had to mill some clearance in it for the aluminum transom cap on my Charger. All went well after I made my engine puller device. I still think I will need either transom wedges or trim extenders to get more trim on my 85 Johny 150. These...
  19. B

    OMC tech series trim gauge needed

    If anyone has this gauge for OMC outboards for sale, please email me at both addresses below. It is the one with the orange needle and rear housing. I have one for the OMC stern drives, but it works opposite. Thanks<br /><br />bmurray@jcn1.com<br />bmurray@hydromat.com
  20. B

    Tach now working

    I followed the instructions at Teleflex about hooking my tach around the rectifier and to the altenator. It suggested to hook the gray sending wire to the yellow striped wire and it is now working and not dropping off after 2500 rpm's. Can I continue to run like this until I get a new...
Top