Search results

  1. T

    Do I need hydraulic steering. Etec 150

    I am thinking of buying a used etec 150 for my ski boat. it's a 21 foot low profile ski boat with the original 1978 Johnson 150. I would prefer not to have the expense of changing the original steering cable over to hydaulic unit. I have been told that the newer etec might have to much torque...
  2. T

    1994 Merc 50 electrical/tach

    1994 Mercury 50 #1060412pt Tach replaced still does not work. Bought new rectifier and in the process of replacing found 2 things. one, can't seem to find old rectifier. Also the 2 yellow wires coming from the regulator have been hot. The wires look fine, however the connectors are slightly...
  3. T

    94 merc 60 tach not working

    I have a 1994 Mercury 60. The Tach was not working so I replaced it and its still not working. The switch on the back of the tach is set to 6p. When I turn the key on the tach moves but does not read with the engine running. Would the rectifier be the next logical step?
  4. T

    Oil pump for 1978 Johnson 150.

    I have a 1978 Johnson 150. I am tired of mixing fuel, so I am looking to find an aftermarket oil pump kit for this motor. I have heard they exist but can't seem to find any info. Any suggestions of where I might find any info on this. Thanks
  5. T

    Which thrust washer. 1978 Johnson 150

    I bought a Michigan Stainless 15x17 prop. Model 389925. The original thrust washer allows the prop to slide down to far. Which thrust washer do I need to make this prop work and where can I order one. The engine is a 1978 Johnson 150. Thanks.
  6. T

    Outboard paint

    I am restoring our old ski boat. Part of the project is a fresh coat of paint on the 1978 Johnson 150 outboard. Any recommendations for paint? Will it peel off if I don't use a two part. Can I get by with something out of an aerosol can? Thanks.
  7. T

    1978 Johnson rebuild.

    While I have this motor off the boat I am considering doing some work to it. Engine runs fine now but has unknown hours on it. What would be required to up the HP a bit? New reeds perhaps, maybe carbs. Any ideas for increased performance on this engine. Thanks
  8. T

    1978 Johnson 150 prop question

    I am currently running a 15x17 aluminum prop. Making about 4600 RPM. I get some ventilation during turns and coming out of the hole if I'm not trimmed full down. I am thinking that a stainless prop may help some. Question is which one and what size. I've been looking at standard 3 blade OMC...
  9. T

    control box plug 150 to 175

    I have a 1978 Johnson 150 I am thinking of buying a 1981 Evinrude 175. Will my 1978 control box be usable on this engine? Thanks
  10. T

    At the prop vs at the head

    What year did they start using power measured at the prop?
  11. T

    1978 150 johnson RPM/prop question

    I have a 1978 Johnson 150 with a 15x17 alum Michigan wheel prop. The boat will run 38 mph at 5300 rpm. However, at that rpm it will ventilate with turns or in rough water. If I trim down to about 4900 or 5000 rpm it will run without ventilation. Also on the hole shot it will ventilate unless I...
  12. T

    1978 johnson wot rpm

    What RPM should I get on my 1978 150 Johnson? What would the max I should run it?
  13. T

    upgrading horse power johnson 150

    I have a 1978 Johnson 150. I have been thinking about trying to increase the performance/ horse power. If I change the reeds do I need to change the carbs. How involved would this little project be? What all would I need to do to get a substantial increase in power?
  14. T

    1978 johnson 150 tachometer

    I need to add a tachometer for my 1978 Johnson 150. What after market tach should, or can I consider?
Top