Search results

  1. Faztbullet

    150 mariner

    Are you trimmed all the way down starting off?
  2. Faztbullet

    Help with Johnson 150 Pinion Bearing Removal

    Did you replace pinion bearing as it was shot
  3. Faztbullet

    1969 85hp Evinrude, CDI Box squeal sometimes?

    Normal
  4. Faztbullet

    Black scuff marks on cylinder walls

    Looks like it scuffed walls and someone honed over the damage and reringed.. a " Bubba" fix. It been punched .030 over sometime in its life.
  5. Faztbullet

    Ruh-Roh… a new gear case may be in order

    You will likely have to swap driveshaft as its fine spline. Most of the 60-70hp 3 cylinder where 4 spline. If you swap shafts you will need to reshim pinion
  6. Faztbullet

    Ruh-Roh… a new gear case may be in order

    Call your insurance company and get a new OEM
  7. Faztbullet

    Help with Johnson 150 Pinion Bearing Removal

    If it chit the pinion for no reason (I dont really see the water evidence) the gearcase may be warped. There is a gearcase alignment tool to check this. I will not rebuild a gearcase unless it is checked. I have discarded cases that look almost new that was warped. If not it will chit the gear...
  8. Faztbullet

    Cost of carb rebuild

    To the original poster.....I charge $95 per carb plus parts. This is removal/install/sonic clean/sync and link. Fuel pump is $95 plus parts. Part would be 4 carb kits @$15.85x4, 4 inlet needles @$11.50 and pump @$31.49 and $16.00 for shop supplies such as fuel ties/carb spray
  9. Faztbullet

    Help identifying fitting. 2000 225

    That fitting gets a cap and zip tie
  10. Faztbullet

    Overide spring ?

    Choke flap spring...prevents flaps from closing at WOT
  11. Faztbullet

    2000 Johnson 70 j70plsis

    Someone cut that or came from factory like that. Sleeves are installed/straightened and block is drilled in middle of transfer port webbing. It is only drilled deep enough to dimple the sleeve and a set screw is installed and epoxied over
  12. Faztbullet

    2000 Johnson 70 j70plsis

    Needs a new sleeve and all sleeves pinned in placed
  13. Faztbullet

    Water in my oil

    Are you running FC rated oil?
  14. Faztbullet

    Water in my oil

    Thats engine oil. Make sure the t-stat is working correctly
  15. Faztbullet

    Recommended DVA meter or DVA adapter for a Fluke digital meter

    If you are a DIY working on your personal engine , buy a DVA adapter and a brand name meter. If your going to work on customers buy a analog DVA in link below. Same meter Mercury sales/uses. FLUKE does not sale a meter with built in DVA adapter...
  16. Faztbullet

    2012 40 HP 3 Cylinder EFI Lower Unit Clutch Dog/Cross Pin Assy

    Check to see if you missed the hole in rod. Goes plastic in shaft, spring compress rod slightly to line up hole in dog. This is not a preload prop shaft but uses desmotronic shifting like bigger motors. Kit is to take some force off shifting process.
  17. Faztbullet

    1993 Johnson 150 -- grinding in reverse

    Check the upper motor mounts as if they come loose (and they do!) it will bend shift rod making it to short
  18. Faztbullet

    Max Throttle on 1995 Evinrude E150 GLEOM

    My 1998 Lowes 24' with 1981 150 V-6 will run 31-34 mph all day
  19. Faztbullet

    Max Throttle on 1995 Evinrude E150 GLEOM

    Not a good idea as spark is at max advance and will create a lean burn.
  20. Faztbullet

    lower unit/ impeller gasket seals

    2 seals on prop shaft, 2 seals on water pump 1 o-ring
Top