Search results

  1. G

    1985 Johnson 8hp parts needed

    Just picked up a 1985 Johnson 8hp. I need a breather cover, and the piece that rides along the carb roller. It's the ramp that rolls along the roller as you advance the throttle. Any help would be greatly appreciated.
  2. G

    1992 Yamaha 3hp tell tale

    I have a 1992 Yamaha 3 hp model 3MSHQ. Where is it supposed to spit water out the telltale indicator? I see two holes on the back of the exhaust leg that it does that water out. Is it supposed to spit out at the back of the powerhead as well? Thanks.
  3. G

    1996 Sears Gamefisher 3hp (Tanaka) outboard problem

    I just bought this motor about a week ago. Cleaned out the fuel tank, petcock, and carb. All was well, and running good. Durring the past few days, I had some petcock problems (old junk plugging up). So I got it flowing good now. Im running marine gas with Lucas 2 stroke synthetic. Compression...
  4. G

    Sears Gamefisher 3hp (Tanaka) parts needed

    I need a good cowl, and a carb silencer cover for my 1996 Sears Gamefisher 3hp outboard. Already tried Sears, but they were long gone. Any ideas on where to get them? Thanks.
  5. G

    1988 Sears Gamefisher (Force) 7.5hp conversion

    Are the Chrysler/Force 9.9/15 same bore and stroke as 7.5hp? Or is the difference in reeds, carb, and exhaust. I'd like to bump up to 9.9 if possible. Anybody ever done this on this motor? I know it has been done on the comcast 9.9/15. Thanks for any help.
  6. G

    evinrude condenser info

    I am looking for a .2 mfd condenser for my Evinrude Zephyr. Original part # is 201753. I was told one from an old 6cyl Ford may work. Don't want to mess up points, or coils though. Any help would be appreciated. Thanks.
  7. G

    Johnson QD16 impeller

    Does anybody know which Sierra impeller I need for my Johnson QD16? I didn't know for sure if the one listed here for newer 10hp would work, or not. Thanks for any help.
  8. G

    Chrysler 20hp information needed

    Thinking of buying a Chrysler 20hp #2033 1969 electric start. Does this have coils, or ignition box? I will check it for spark when I look at it tomorrow. It's missing the tiller gear/shaft assembly on the motor side (half). Any thoughts on the ignition setup? Motor has 130# compression...
  9. G

    Chrysler 20hp tiller part needed

    Chrysler 20hp mod # 2033 (1969???). I need the tiller gear/shaft setup. Also ignition key/switch. I would appreciate any help. Thanks.
  10. G

    1970 Evinrude 6hp part needed

    I need the throttle cam plate, and the follower (mounts on carb linkage). Thanks.
  11. G

    1957 Johnson JW13 3hp decals where to buy?

    1957 Johnson 3hp JW13. Anybody have any ideas on where to get decals? :)
  12. G

    Mercury 3.9hp (39) reproduction decals wanted

    Does anybody know where I can get decals for my '68 Mercury 3.9hp? Any help would be appreciated. Thanks. ;)
  13. G

    Eska 15hp spark plug selection

    Plugs in the motor now are equivelant to Champion RJ18C heat range 18 My manual calls for RJ12YC heat range 12. Champion website calls for RJ14YC heat range 14. My motor does not have a thermostat currently. Thermostat was missing when I got it. I'm guessing that's why they put in the hotter...
  14. G

    Eska 15hp fuel fitting leak

    On my Eska 15hp (Tecumseh powerhead), my fuel fitting leaks fuel (female end) when I disconnect from my motor. I can hear a hissing sound when I hold fitting higher than the tank (fuel being pulled by gravity back down into tank)? Primer bulb is mushy. I think o rings are sucking in air while...
  15. G

    82 Evinrude 50 want to add a tachometer

    Is there a way I can add a tachometer to my 82 Evinrude 50hp? I would like a round analog gauge to mount in panel. Anyone done such a thing on an older motor? What is a descent brand tach that will work for me? Thanks.
  16. G

    82 Evinrude 50hp bad idle

    82 Evinrude 50hp runs great all day at top, mid, and low rpm. It just won't idle. Seems to choke out at idle like it's getting too much fuel. Carbs freshly overhauled with new floats, gaskets, needle and seats. Float levels even with carb body. Timing is advancing, and retarding with throttle...
  17. G

    Evinrude 50hp has 1 wet plug?

    82 Evinrude 50hp. Top plug is good, lower is wet. Coils are firing (checked by inductive timing light). Champion plugs. Don't want to idle. Could my lower carb float be to high? What are symptoms of a high float? Possibly a leaking float? CDI was changed out, and same symptoms? Thanks for any...
  18. G

    82 Evinrude 50hp problem

    I am having trouble with my 82 Evinrude 50hp. Won't idle very good. Carbs have been cleaned 3 times (and once before I owned it by local marina). Top plug looks good, bottom plug is wet with fuel. I was testing on ear muffs and it took off to mid rpm's and just hung there. I killed ignition with...
  19. G

    60's omc 25hp impeller housing needed

    I am thinking of buying an early 60's Sea King (OMC). It needs impeller housing. Anybody know where I could get one? Thanks.
  20. G

    Johnson/Evinrude tell tale modification

    I have a 1970 6hp Evinrude. I want to add a tell tale to it. Has anyone ever done this on a smaller outboard? I read other post on here that was for the larger outboards. I appreciate any info. Thanks.
Top