Search results

  1. M

    Trying to decide on a boat Type Ect

    Hey. I am finally deciding to get back into boating and was looking for some ideas. I am trying to find a smaller boat (14-16ft) that can hold 4-6 people and weighs less than 2000lbs. I dont want a fling/rage/mirage ect.. I would like an I/o rather than an outboard (just a personal...
  2. M

    Johnson Crossflow changeovers

    Would a 98 Johnson 88 horsepower (http://annarbor.craigslist.org/boa/3129892999.html) like this, work on a 94 115 crossflow lower unit? I know the bubble back would have to be moved over and the carbs to make it the 115. Its just like this one, just the lower unit is bad but the power head is...
  3. M

    94 Four Winns Fling Wont stay running

    Hey guys, My 94 fling will not run for more than 10 minutes before it stops and will not start again for awhile. I tested the alarms for the overheat to make sure they go off, they do, and checked the timing ect. All of that is fine. Compression is like new. I am unsure what could cause...
  4. M

    94 Johnson 90 hp cross flow no Spark :Stator Issue?

    Hey all. I have a 90 hp johnson that is getting no spark at all from what I can tell. I have checked the timing base and the power pack came off another motor. What else or how else can I test for spark issues. What all controls it? Its a 94 Johnson 90 hp Cross Flow. Would the alarm...
  5. M

    Carb to motor?

    I have a set of carbs someone is trying to sell me as 140. is there any way I can tell. They are for a 140 johnson crossflow, 83. Say 1 5/16 stamped on them.
  6. M

    Couple questions on a 115

    Hey guys I have a johnson 115, 82 crossflow. I need the electric fuel pump number for one that does not do oil injection if anyone has it. Ill mix the gas. Also the warning horn for whatever reason was removed. Im thinking Ill just run two tempature gauges, one for each head. Any one have...
  7. M

    Block Boring and honing

    Hey guys I was wondering if anyone knew of a good place that was reasonably priced to send out my block, preferably in Michigan if possible, to get the cylinders bored. I have called a couple places and gotten everywhere from 65 bucks a hole to 25 a hole from a place in Florida. Also were would...
  8. M

    Would this motor work in place of a 115?

    Hey I have a 94 four winns fling that had a 115 hp motor in it. I was wondering what the difference on the 110 is I found this one crossflow - serial: # r 08211046, model: j110tlcem and was wondering if it would bolt right up and the shafts would be the same ect. Thanks
  9. M

    What kind of motor is this?

    I have a model number J115TLCNB can you tell me if its a cross flow, I think its an 84. Thanks
  10. M

    JOhnson Serial, what it means. Need help asap!

    j4572519 MOdel is 115e176g CAn any one tell me year, ect on this Also if its a cross flow or a looper thanks a ton!
  11. M

    I have the serial to a johnson motor what is it?

    Model #- J115ilcnb Serial #- j5715986 I know its a johnson 115 is it a cross flow or looper though cant tell from the numbers.
  12. M

    Johnson 140

    s# J5162266 m#140TL79R is this a looper or a cross flow?
  13. M

    95 v4 crossflow to a 92 crossflow

    These bolt up exactly the same correct. J115TLEOR is the 95, pretty sure its a cross flow, pistons are not flat but curved like it so yea. Finally can a 95 one be resleeved, its bored .030 over already and the biggest piston kits I found are only .030 over. Wisco had one thats .065 over but...
  14. M

    Looper and crossflow, 60degree and 90 degree

    Ok I was shopping for some new parts last night and I was thinking the looper is a 60 degree motor and the crossflow is a 90 degree. Is that right. Also just by looking is there a way to pull this off the serial or model number. Everything I found on the model number doesnt seem to tell me...
  15. M

    Johnson 115/90 crossflow powerhead questions

    What years would match up to a 94 fling motor, omc/johnson 115 crossflow from what I have gathered. What years would match up for the power head? The Bottom needs to bolt up the same and that. My power head cracked the short block. So I need to find a new one and found a early 80s and wanted...
Top