Search results

  1. C

    Overheat / dry run Yamaha 115- Need advice

    Thanks, I am trying to determine how serious it was? Assuming 5-7 min on idle runtime w/out water on an 80 degree day. What is the likely outcome? Do you know where I can get torque specs?
  2. C

    Overheat / dry run Yamaha 115- Need advice

    Its a 2017 4 stroke with 100 hours. It's half mine. Thanks for the feedback
  3. C

    Yamaha F175XA Cooling System Problem...help?

    Something wasn't put back properly or was damaged, pics would help. Did you replace the water pump housing? If not make sure there isn't any melted plastic blocking the passage to the water tube. If you did replace make sure you moved the clip and rubber seal for the water tube over from the...
  4. C

    Overheat / dry run Yamaha 115- Need advice

    Here's the story (I was not there). Boat was started and left unattended while he went to get the trailer. Got back to boat to discover the engine was trimmed all the way up out of the water and overheat alarm beeping. He said it was running for approx 5 minutes w/out water. However, said it...
  5. C

    Remove Mercruiser throttle cable guide?

    Yes, throttle cable. Shift cables are a-ok. Thanks again for the help.
  6. C

    Remove Mercruiser throttle cable guide?

    It's a 3.0 I/O from 2004.
  7. C

    Remove Mercruiser throttle cable guide?

    Uggg, no set screws or rivets. Just the silver barrel at the end. Thanks for the quick reply.
  8. C

    Remove Mercruiser throttle cable guide?

    Can these be removed? Cant locate any screws. How do I remove the metal anchor retainer in the attached pic? Thanks
  9. C

    Mercruiser Gen II trim problem

    Trim has trouble moving up (very slow). Rams are good, can't find any leaks anywhere in the lines. However the pump struggles and aerates the pump oil (and appears to be leaking a bit of oil, can't tell from where). I have bled the system a couple times and it improves for one cycle then back...
  10. C

    Mercruiser 3.0 carb rebuild

    Just rebuilt the 2 piece mercarb on a 3.0. Question, the diagram shows a strainer screen, clip and check ball under the accelerator pump. Mine does not have these, however it's been opened before and they did a lousy job. Are these supposed to be there? Whats there function? They didn't come...
  11. C

    Mercury alpha one Gen 2 gear oil leak

    Just picked up a boat on the net for a good price and in the process of getting her up to speed. It has been sitting for about 5 years. Gear oil was leaking from the lower water intake grate (port side), Drained (no water in the oil) and refilled. No leak for about 6 days, now it is leaking...
  12. C

    Suntracker party deck fuel sending unit

    Filled my 2004 Suntracker party deck 21 with gas at the beginning of last year and now the Guage is stuck on full. Can't find any easy way to access the sender. Anyone have any ideas? I followed the gas lines down to the tank; however, would have to pull the seats out to follow all the way...
  13. C

    Removing hull residue

    I have acid washed my fiberglass Sunesta 232. Most of the algae and water stains have come off; however, there is a black residue on the port side that won't wash off. I tried muriatic and commercial hull cleaner and neither will remove it. Any tricks? Thanks
  14. C

    Mercury 125 knocking noise

    Any help is appreciated. My 96 merc is knocking when I accelerate. It doesnt have the sound at idle or in neutral and goes away at full throttle. Any Ideas?
  15. C

    Pontoon with XL Shaft (25 inch) motor

    Anybody have a 25 incher on their toon? If so that kind of results have you had?
  16. C

    Mercury 135, 150, 175?

    I am of the understanding that the block is the same for mercury 135-175hp. What is the differnce between them? Can I make a 135 a 150 or 175? Thanks
  17. C

    Merc 125 flywheel stuck

    trying to get the flywheel of my 125. I broke the bolt off the puller and it didnt budge. Any thoughts?
  18. C

    Mercury 125 High Speed Miss

    I have a 1996 125 that has an occasional High Speed Miss. It has a new switch box and regulator. When it misses, bringing it back to idle and then to WOT a couple of times will clean it up. Any suggestions? Thanks
  19. C

    Mercury 125 ignition, voltage problems

    I have a 1996 merc 125 that has a couple problems. I had the boat out this weekend and it ran great at idle; however, would not rev over 3000 rpm under load (fine at idle). Also, the voltage meter was reading in excess of 16volts. I did a quick look over of the motor and in looks like...
Top