Search results

  1. J

    1954-55 Elgin 2hp Mag drwg. and parts list. I need em'.

    I picked up a free Elgin 2hp and have no spark. Coil was sitting loose with no wires connected when I removed flywheel. Coil checks bad and points are shot too. Compression is good. I need a schematic and part numbers for this mag. I know it's probably worthless but I'd like to get it running...
  2. J

    86 15hp johnson longshaft-Mod#15RLCDE

    I have removed the gearcase for waterpump replacement but cannot get the 5"extension to come off the midsection. I managed to drop it down enough to get the shiftrod disconnected but this extension will not come loose. This is a saltwater exposed motor. I should say "saltwater abused". The...
  3. J

    120hp Johnson- no data plate

    Hey guys- Just picked up a 86-89? 120hp Johnson. No data plate anywhere. One softplug with #G2252562 on it and according to Marine Engine.com- it's not a valid number. What now?? I want to get a factory manual on this thing and I gotta know the model number. Where else do I look? Thanks Jack...
  4. J

    Late 80s 120 hp Johnson questions

    Two questions guys: #1- No data plate on motor. Where else is the model and serial number to be found on these late 80s motors. It supposedly is a 89 but the guy that owned it is almost 90 years old and can't remember for sure. #2- This is a VRO unit and what's the procedure for changing to a...
  5. J

    1960 10hp sportwin powerhead removal

    How do I remove the powerhead from my Model 10020 3501 Evinrude??? I'm not having any luck. seajack440
  6. J

    Evinrude 1960 10hp Sporttwin

    I just pulled the lower unit and the driveshaft is stuck up in the crank. Model 10020. Turned motor upside down and flooded shaft with Aero Kroil.Let it set all night. Still stuck and I'm not looking forward to pulling the powerhead to get it out. Any you guys have an idea how to proceed...
  7. J

    75 9.9 Evinrude-electronic ignition

    I have a 1975 Evinrude 9.9hp motor that has an electronic ignition system. The factory service manual and the parts book says there's no such animal. Model 10525C Serial 0001284 Any of you guys know of a conversion that could have been done? Also have a 1975 Johnson 9.9 and it has the driver...
  8. J

    WTB-Parts book for 1973 7.5hp Merc

    I have a 73 7.5hp Mercury that is in sad shape. Saltwater motor. I need a parts manual for this motor. Where can I get one? Serial #3729161. Thanks seajack
  9. J

    9.9 lower unit interchange.

    Another question guys: Will a 1979 9.9 hp Evinrude lower unit fit on my 1975 9.9 hp Evinrude? Jack Mears Concrete, Wa.
  10. J

    Need Montgomery Ward outboard imfo

    Hi Guys: I picked up a Montgomery Ward Model VWB 52119A, Serial #OX8 21954. What horsepower and year is this motor? I need a waterpump impeller and pump seals for it. Any ideas where I can get a parts and service manual for this motor? It appears to be in good shape and too good to chuck...
  11. J

    1994 5hp mercury

    Hey Guys- I'm gonna ask again if any of you can lead me to the hood markings on my 1994 5 hp Mercury. It's currently all black. Serial #OD 934548. Made in Japan. Single cylinder and noisy as hell!! I know if this was a Johnnyrude I'd have 10 replys by now. But it ain't. Thanks
  12. J

    1994 5hp Mercury

    I picked up a 94 5hp Merc and the cowl is painted black, Black only! Looks like the previous owner didn't like the Merc decals or whatever so he scraped em off and painted the whole thing black. I need a picture or source for the original cowl trim. Motor runs well but looks like Darth Vader...
  13. J

    56 Evinrude 5.5hp gas/oil mix

    I just fired up an old 56 5.5 Evinrude. Dual hose setup. Mixed 24/1 in tank. She ran fine for a while in the test tank for a couple minutes in gear, then started slowing down, then quit. HARD to pull when I tried to restart, really hard. Like she's seizing up. Is 24/1 mix too little oil and...
  14. J

    79 140hp trim problem

    I have a 1979 Evinrude 140 hp with power trim/tilt. It's not hooked up electrically. I manually tilted up motor to install lower unit by opening the hydraulic bypass screw. Now that the lower unit is installed, I lowered motor but the trim rods came up and don't allow the motor to return to the...
  15. J

    5.5 hp 1956 evinrude fuel hose conversion

    I have a 56 5.5 Evinrude with the double hose/pressure tank required. Is there anyway to convert this motor to the single hose Evinrude/Johnson newer models? The pressure tanks are more dear than gold on ebay as are the hose fittings.: Thanks Jack Mears Concrete, Wa.
  16. J

    Deposit on 79 140hp Evinrude piston crown

    I just pulled the heads on a 1979 Model 140943R bubbleback. All pistons are stamped .030 on the crowns. Three of them are almost new and the crosshatching is still visible on the cylinder walls from the rebore. The port lower piston crown and plug have what looks like lead deposits on them...
  17. J

    WTB- 1978 140ml 78c bare block-Johnson bubbleback

    My 1978 140 hp block has one cylinder that has already been rebored to .030 oversize and it needs more. As I understand- .030 is the max rebore. The Johnson numbers are: Mod. 140ML 78C, Ser. J4984501. I want to buy a replacement block that is the original bore (3.50") or at most, .010 oversize...
  18. J

    5.5 Evinrude shift problem

    Hey Guys: I just sold a 1962 5.5hp Evinrude a few days ago. Cheap! Model #5522. Tested it in the tank for the guy before he bought it. All OK . Today he brings it back, says the prop don't turn when he puts it in gear. Back in the tank. Sure enough, she's a no go. Shear pin OK. Anyone have any...
  19. J

    78 140 Johnson

    I have a 1978 140hp Johnson. Have a chance to buy a 1979 140 hp Evinrude for parts and the power tilt unit which my Johnson doesn't have. Also a better powerhead than my 78 which I have opened up and it needs a rebore on one cylinder. My question is: is the 79 140 Evinrude about the same as my...
  20. J

    59 18hp Evinrude remote elect. cable

    Here's another one guys: Have a 59 18hp Evinrude electric start. Model 15028, serial 17266 It's got a plug in the lower cowl to connect remote start, kill, choke and both battery cables. Two large (1/4" +/-) male and three smaller tits (male too) Trouble is that from what I'm told they only...
Top