Search results

  1. Scode68

    Stalling at Idle and Idle Speed

    It’s a poly Moller tank.
  2. Scode68

    Stalling at Idle and Idle Speed

    There is no panel to remove to take the tank out and I would have to cut a flat deck and hope I'm cutting where it has to be cut. Not to mention that it will look like total crap when glued and filled back in. I'm realty hoping that there is a screen on the end of the pick up tube or I'm...
  3. Scode68

    Stalling at Idle and Idle Speed

    Just following up, Hooked up the portable tank upstream from the primer bulb so I would have 2 in there. Both bulbs got soft but did not empty and I ran the boat at idle for 45 minutes without so much as a hick-up. Issue has to be the tank pickup tube and probably gunk in the tank clogging...
  4. Scode68

    Stalling at Idle and Idle Speed

    I'm trying to do as much BPR parts as I can but some things are just not out there. I've seen kits on Amazone with a wide range in pricing but I think the difference is just the person selling the kits. I'll have to look at the pulse fitting.
  5. Scode68

    Stalling at Idle and Idle Speed

    I think it’s just a matter of getting a good kit. Lots of Chinese kits on Amazon.
  6. Scode68

    Stalling at Idle and Idle Speed

    No but 88 refereed to posts 3 & 4 where it said to change out the bulb. And it was mentioned in post #11 that it was done with no change. Fuel pump is $600 so I just didn't want to change that out just for trying. I was thinking of pulling the tube this off season cause nobody could give me...
  7. Scode68

    Stalling at Idle and Idle Speed

    Yeah, it was tested by the marina mechanic where I keep the boat and I pulled it so I could bring it up the creek to Evinrude guy. The Evinrude guy has a great reputation and when he said the fuel pump was tested to be fine I believe him. That's not to say that in a month that it couldn't have...
  8. Scode68

    Stalling at Idle and Idle Speed

    Read post #11.
  9. Scode68

    Stalling at Idle and Idle Speed

    The compression is 100psi +- 1 or 2 psi. I'll have to test this with the 6 gallon tank for my 20 Merc when I feel a little better. So you think it might be the fuel pump?
  10. Scode68

    Stalling at Idle and Idle Speed

    J200VXSIF 12/2000 I didn't pull that pickup tube yet but couldn't get a straight answer from anyone if there was a screen at the end or not. Tried multiple time contacting moeller but they never returned my calls or emails. I haven't found water in the fuel yet. Nothing collects in the...
  11. Scode68

    Stalling at Idle and Idle Speed

    Been under the weather this week so I havnt done much. I swapped out the primer bulb with no difference observed. I even ran the boat with the fuel cap cracked open and no difference. This summer the carbs were rebuilt, all fuel lines from the tank to the fuel pump were replaced and I...
  12. Scode68

    Stalling at Idle and Idle Speed

    Carbs were rebuilt by me and then an Evinrude Johnson mechanic. BPR kits were used both times and mechanic an ultrasonic cleaner. He is good and would trust him with any work.
  13. Scode68

    Stalling at Idle and Idle Speed

    Since the motor has been ruled out I’m pretty sure I’m asking about the fuel related system. Fuel cap to the primer bulb. I’m looking to find out what in the fuel system would cause a fuel starvation at low rpm, but not at higher rpm’s.
  14. Scode68

    Stalling at Idle and Idle Speed

    I was going to but I have a feeling this isn't motor related. Had the mechanic at the Marina (Mercury Guy) look at it back in August for a non-running issue. Then I pulled the boat and brought it to my Evinrude guy that rebuilt the carbs and tested the ignition and fuel pump. Yesterday it...
  15. Scode68

    Parking boat in driveway

    Same in my down and the town my Dad lives in.
  16. Scode68

    Stalling at Idle and Idle Speed

    new problem found yesterday. While I'm idling or just just in gear at low speed in a No Wake Zone the motor stalls like I'm running out of fuel. While running at speed the motor runs normal and doesn't stall. Fuel primer bulb is soft but not collapsed. Have a vent fuel cap but when cracked...
  17. Scode68

    Fuel Dripping From The Carbs When It's Hot Out - 200HP Johnson 2001

    Should have said where you got the information from. I’m not on here to disrespect anyone here but if I don’t have all the information I can’t make the decision.
  18. Scode68

    Fuel Dripping From The Carbs When It's Hot Out - 200HP Johnson 2001

    Yeah, but where did you get this from?
  19. Scode68

    Fuel Dripping From The Carbs When It's Hot Out - 200HP Johnson 2001

    I just went to pick up the boat. I had initially installed a shutoff valve and that worked. I then developed a hard start issue and everything from the tank to the fuel pump was ruled out. I rebuilt the carbs with BRP kits and torqued to factory specs. Then the motor would start for about 5...
  20. Scode68

    2001 200hp Carburetor Torque Specs

Top