Search results

  1. quikstang347

    Yamaha 130 Temp sensor issue

    Model # S130 TLRU Recently i had an issue with the oil injection and have rectified the issue i am sure this is a temp sensor problem. Ok here it goes while running the boat at 4200 + rpm's the alarm would sound and the motor would go into limp mode, so i have begun my investigations. i...
  2. quikstang347

    I Need a lil help with low oil alarm on precision blend 130hp yamaha

    Ok I have spent days reading and testing everything that has been posted on here about the precision blend system. I am very mechanically inclined and have not found the issue yet . here is the sympton Just purchased a flats boat and it runs great i have no issues at all . after a few moments...
  3. quikstang347

    need help installing a reverse rotation camshaft in 454

    i have the 454 out of my boat and rebuilt it . after all the machine work and assembling . it is ready to go. i turned the crank over by hand and it does not rotate the entire way. i then proceeded to pull the valve covers and take the pushrods out. it now turn over fine. my question is there...
  4. quikstang347

    is my motor supposed to be standard or reverse rotation

    i bought a 28' silverton it has a single 454 and a v drive for the trans. i disassembled the motor and it has been rebuilt before. it has a large cam gear to a single crank gear . this is reverse rotation. my question is that with someone being in the motor, probably more than once is it...
  5. quikstang347

    porposing help

    i have a nice 79 mako 21 it has an Evinrude Ocean Pro 175 the problem is i am having issues with the thing porpoising it takes a long time to plane maybe 8-12 seconds. once on plane it runs great except for when i hit a small wave maybe 2-3 ft it starts to bounce and will eventually settle down...
  6. quikstang347

    95 Ocean Pro hard to start then runs fine

    thanks for looking i appreciate all input on this issue. I have a 95 Evinrude 175 Ocean Pro . it runs great when running. if i use the boat and then let it sit for a few days then go to use it again . it is a heck of a time to start it. takes forever. just the other day i ran 100 miles in it...
  7. quikstang347

    need mariner inline 125 piston help

    ok here it goes took mariner inline 1997 motor apart and seized a ring to the piston.; the problem is i can not find the piston i need. the motor is 1997 mariner 4 cyl inline 125 hp the motor has been rebuilt before and the bore is .030 over now . the piston that came out of it says "582" on...
  8. quikstang347

    Just stopped charging ???????????

    ok had wiring issues with this boat . so anyhow got them straightened out today . everything works it starts stops and so on . put it in the water for fishing trip in the morning . starts right up everything good and ready . all of a sudden i notice i am not charging. i did install a new...
  9. quikstang347

    Will not shut off by key

    my 95 evinrude ocean pro 175 just developed this problem . it starts runs fine and has no issues other than it will not shut off. i checked the lanyard and disabled it ran it to a toggle to shut it oiff for the time being so i could use the boat . but it does not always work. sometime it will...
  10. quikstang347

    Evinrude 175 No spark on one side of motor HELP

    . hello every one , decided to get my mako it has an evinrude ocean pro 175 (1995) ready to run this weekend and take her out. everything has been fine with it , have had it several times no issues at all. yesterday i hooked up the tach and volts as well as water temp gauge . everything was...
  11. quikstang347

    97 Mariner 125 Compression issues

    Hello to everyone on this site i am newly registered here but have been reading the forums for years. I have a question to pick your brains, i just recently purchased a 19' trophy center console with a rebuilt 125 mariner on it. Yes i have the paperwork and talked to the marina that did the...
Top