Search results

  1. M

    dumb idea or genius? w/pic

    Needed to replace a couple of rollers on my trailer. Went down to West and picked up the rollers and new shafts. First off I noticed the end caps that came with the shaft were cheap and would have rusted off in a month. I could have gotten the galvanized caps but didn't think about it...
  2. M

    What is this? (pic)

    and where can I get some. This hard plastic moulding is what my spray hood attaches to. It is starting to crack and I would like to replace.
  3. M

    What wood should I use? (pics)

    I want to build a storage area in my boat. What wood should I use. It will be completely glassed in. I have done a lot of fiberglass work before but just not sure what wood to use. A buddy suggested mdo plywood. Any suggestions or comments on structural issues. I plan to put a hatch in...
  4. M

    Engine too low? (pics, specs & Performace) NOT anymore!!!

    Raised the engine two holes and did some performance tests. I think I'm good to go. Avg slip of 12.85% from four WOT test runs. No overheat or cavitation issues. Cav plate is clearly visible. Much less spray from around the cav plate. Might try a 19 pitch if the opportunity is there. Big...
  5. M

    Privateer Help!

    Does anyone own or know someone who does? I have an 1984 with an 2008 Yami 90 2strk. I would like to compare engine mounting height and prop / pitch.
  6. M

    Yamaha 90tlr - How to drain the carbs - the correct way.

    Its a 2008 two stroke. with 40 hours. Had the 20 hours service. Of course, I run the corn laced gas. I probably wont use the boat for a month or so since its January and getting freakin cold. Ok it's Charleston SC but its cold to me. Rodbolt says - you are not going to drain all of the gas...
  7. M

    Steering Rod Link help. Yam 90 2strk

    Just got a 2008 Yam 90 2 stroke. Noticed that the boat has more steerage going to port then starboard. Checked it out and the steering rod seems too short. When steering to port the engine will turn until to the stops (on the engine). When steering to starboard steering cable fully retracts...
  8. M

    Help! with hole in my deck

    Anyone see any issue with my plan to fix the hole? I have worked with fiberglass a good bit so it?s a given that surfaces will be properly cleaned and prepared. Went out last weekend and someone was sitting in a deck chair in the front of the boat. Hit a big wake and the person and chair...
  9. M

    Northstar F210 fuel flow meter

    I'm thinking about ordering one of these for my Yamaha 90 two stroke. Have searched the forums and it seems that most everyone has had an issue with these units. Anyone out there that hasn't had a problem? Any input (good or bad)? thanks
  10. M

    NorthStar F210 fuel flow meter

    I'm thinking about order one of these for my Yamaha 90 two stroke. Have searched the forums and it seems that most everyone has had an issue with these units. Anyone out there that hasn't had a problem? Any input (good or bad)? thanks
  11. M

    Seloc Repair Manual on iboats - Good or Bad?

    What about the online subscription? Any input? thanks
  12. M

    Peformance for HWSiii - THANKS!!!

    Hwsiii - You nailed the mph exactly. Thanks so much for your and others help. Anyone reading this -Hwsiii and the other "prop gurus" know that they are talking about. Post your questions and give the information they are asking for. Pictures help. Question - Do you think I should go up...
  13. M

    Is this engine mounted too low? (pic)

    Boat seems to drag over 4000 rpms. Only getting 4500 rpms and WOT and trimmed up. 1984 18 Privateer, 1250 dry weight, 2008 90 hp Yamaha 2 stroke (8 hrs) Michigan Wheel Apollo Series 13 1/4 by 17" SS prop. Any help would be greatly appreciated.
  14. M

    Did the Dealer install the wrong prop?

    First off, thanks everyone for all of your expert knowledge you post to this site!!! I just repowered my 18 cc with a 2008 Yamaha 90hp two stroke. Broke in the engine this weekend. The prop that was installed was a SS Michigan Wheel Apollo Series 13 1 / 4 by 17. This prop would hit the...
  15. M

    90hp 2-stroke break in suggestions?

    Any suggestions other then whats in the manual. The dealer said - Follow manual - the first 10 minutes (done at the dealer) Follow manual - the first 50 minutes don't exceed 3000 rpms, vary engine speed occasionally Follow manual - the next two hours don't exceed 4000...
  16. M

    2008 Yami 90hp 2stroke - Spare Parts on board???

    To RodBolt and the other Yamaha experts - What spare parts, tools, hoses...etc should I carry to get me back to the landing. Just bought a 2008 90hp two stroke for my 18 Privateer. Breaking it in this weekend. Spare 10 micron filter. Extra oil Spare plugs, plug wrench.
  17. M

    08 Yami 90hp anode tab is flush with cav plate

    Just repowered my 18' cc. Picked the boat up yesterday evening. Got home and noticed the zinc tap does not protrude down in front of the prop. In fact it can't because it would hit the prop. It's there in the mount but looks like the tab was cut down flush so the prop would clear. Prop is a...
Top