Search results

  1. L

    2003 Johnson 175?

    Motor runs extremely well until complete wide open throttle then it drops between two & three hundred rpm & speed slows down until i let off of hot foot a little while & it picks back up & then after a bit it does it again. I can repeat this at will over & over, but as long as i slow down for a...
  2. L

    2003 Johnson 175 ???

    Model number J175GLSTA. Does this motor have a rev limiter ??? If so at what rpm does it activate ??? Thanks
  3. L

    1995 Dyna Trak 180 STE ???

    Has anyone ever had one apart ??? I've been offered one in trade for my 98 Xpress H-56 & wondered about the construction of them. Also give me the good & bads of these hulls in this particular year model please. Thanks
  4. L

    Waht Prop Is This ???

    Numbers inside it are 284clu or maybe cul. Can't remember for sure, but it's been worked evidently & has E3 & 26p inscribed on the outside of it. It's a 4 blade. Thanks
  5. L

    Wanting to check Mariner overheat alarm

    1998 Mariner 135. Anyone have detailed pics & instructions on how to check to see that it is operational ??? Oil injection has been removed so no alarms at startup. Just bought used & figured better safe than sorry. Thanks
  6. L

    Prop Starting Point

    1998 Xpress H-56 witha 1998 Mariner 135. 2:1 gear ratio & no jackplate. What 3 & 4 blades would you guys reccomend that I try ??? 5600 is max rpm for this engine. Thanks
  7. L

    1998 Xpress H 56 Wiring help ???

    Does anyone by chance have a wiring diagram ??? Wanting to clean up previous owners mess. Will be replacing the old glass fuse box with a new blade type fuse box & rocker switches too as some of them are bad & want to simplify everything & be neat & proper. Thanks
  8. L

    hole in bottom of boat ???

    I have a small hole in the bottom of my boat about 1.5 inches around where a stick drug up between trailer & hull when loading. I siliconed it as soon as I got home & it doesn't leak. What do I need to fix it ??? There are also a few scuff marks around the bottom of the hull that don't leak...
  9. L

    92 Johnson 70 HP Trim ???

    Went to trim down today & it wouldn't from helm or the engine trim switch either one. It will however trim up from either. Can feel relay clicking when using the down position & don't feel anything when trimming up. I'm assuming this realy is for the down position only.It does have 2 relays & I...
  10. L

    Dead Rise

    I bought a 1993 Sprint 255 from a buddy & he installed a Humminbird 525 depth finder. It doesn't read right. If your sitting still it reads right sometimes & all of a suddun it goes to reading 0.9 ft. When moving on plane it's right everytime. My??? is how do I measure dead rise so I can remount...
  11. L

    new onboard charger mountung

    I bought a new Minn Kota 15 amp 3 bank charger. Will it be all right to mount onto inside of bass boat that is carpeted or will I need to take some of the carpet out??? I'm talking about mounting it under the rear deck lid where the gas tank & batteries are. Thanks Just wondering if the...
  12. L

    How to check powerpack???

    1979 Johnson 70 hp. How do i check power going to & from the powerpack???It was running fine & all of a sudden while idling, it died & wont start back & plugs not firing. What color of wires should i check??? If someone knows what kind of reading should I get before & after going through...
  13. L

    Motor not firing

    Model # 70ESL7.5B. No blown fuses. What would be some other common things to look for & how to test??? Controls have been replaced. Ran fine for several trips & was idling & all of a sudden died & will not start back. It isn't firing at all. Thanks
  14. L

    Hwsiii

    I purchased a 13&1/4 by 17 Stiletto stainless prop(same pitch & diameter ) as the original aluminium that came with engine. Dropped rpm from 5900 to 5500. Now boat is a lot slower coming out of the hole. Throttle isn't nearly as responsive as with aluminium , but stays on plane at less rpm. I...
  15. L

    What does this prop fit ???

    Michigan prop # p539 ssc-317-11-c ???
  16. L

    Hwsiii :Going from aluminium to stainless

    Some major companies tell me going from aluminium to stainless in same size & pitch will drop rpm some, others say it will not. I'm running a aluminium 13&1/4 by 17 pitch turning 5900 rpm. Tried a 13by 19 turning 5800. Tach is right & verified by mechanics tach. What stainless pitch will drop...
  17. L

    Think my tach is wrong.

    What woulb be a good one to get to go on my 1992 70hp Johnson & also be easy to install. I'm trying to find a prop & don't think my tach. is right because a 13&1/4 by 17p turns 5900 rpm & a 13x19p turns 5800 rpm Thanks
  18. L

    Hwsiii

    Running down Lake Cumberland last night & of course I hit the only peice of trash on the lake & broke a blade off of my prop lol. Now I need a new one. I have a 1993 Sprint 255 with a 1992 70H.P. Johnson turning 5900 rpm. Thinking stainless what do you reccomend ??? I want the most top end I...
  19. L

    Anyone have any suggestions???

    On how to properly mount the transducer on the back of the boat for a 525 Humminbird??? Works right when running down the lake, but will be working fine while fishing(showing the correct depth) & all of a sudden it shows 1 foot or .8 or .9 ft.. Then after a little of this it straightens out &...
  20. L

    Aluminium to stainless

    Have a 13x17 pitch aluminium prop turning 5900 r.p.m. If I try a stainless what do I need to try. Boat is a 1993 Sprint 255.
Top