Search results

  1. krs60

    1972? g-w invader drag n ski rebuild attempt

    I am also a member at fiberglassics.com (which is down at the moment) and I usually post over there. I think it's because my boats are glassics. I realized it would be no problem if I posted here instead so here we go... I have a G-W Invader 14 foot drag n ski I want to restore/rebuild. I...
  2. krs60

    1975 mercury 650 no spark

    Does anyone have a link to a troubleshooting guide for this motor? I do not have spark. Parts replaced are complete distributor, coil, switch box, and the mercury switch. Maybe i'm missing something???
  3. krs60

    quicksilver control cables or ends

    I have an old quicksilver control but cannot seem to find the correct cables or ends to fit my 1959 merc mark 35a.
  4. krs60

    mercury 35a wiring and ignition switch questions

    I cannot find a manual or wiring diagram showing where the wires coming out of my 1959 merc mark 35a go to. Wires at motor harness that i'm unsure about are 1-solenoid, 2-choke, 3-magneto, and 4-rectifier. I know where the positive and negative cables go Do i use a 5 pole push-to-choke switch?
  5. krs60

    throttle and shift cables

    Does my 1958 evinrude starflite fat 50 use type "400" control cables? I assume it does. http://www.iboats.com/Evinrude-Control-Cables/dm/*******.258483510--session_id.579282929--view_id.243426 Second, is the same cable used for throttle and shifter or are there seperate cables?
  6. krs60

    parts for 1958 evinrude starflite 50hp

    Where the heck do i get parts for my 58 evinrude starflite 50hp? I need a water pump impeller. Google gives me nothing!
  7. krs60

    brass prop question

    I googled and used the search here on the forums with no clear answer. What is the deal with brass props? Are they vintage? How are they performance wise (better or worse than other props)? I've only seen one before...it's on my 58 evinrude 50 starflite. Thanks.
  8. krs60

    wiring question

    I'm trying to get my boat running and on the water asap and do the finish wiring as time permits. My question is...what needs wired to start motor and for it to keep running? My guess is the electric choke and ignition switch. Navigation, horn, lighter, etc can be done later. Am i correct or...
  9. krs60

    shoebox cap

    Are shoebox joint caps available new? Searched Iboat forums and Google with no luck.
  10. krs60

    gas out of carbs

    Gas is coming out of the mouth of my carbs. I rebuilt both carbs on my 1977 Mercury 850 85hp and i know i adjusted the floats to 11/16". Both idle mixture screws are 1 turn out from lightly seated. I did replace the needle and seats. Any ideas? Turning the idle mixture screws in (clockwise)...
  11. krs60

    carb rebuild kits

    I did a search but do not see my motor listed. I have a 1977 Mercury 850 85hp and need carb rebuild kits. Motor # is 4537704. Thanks.
  12. krs60

    sealant versus sealant

    Would the 3M 4200 be ideal for sealing the 2 halves of my 1960 slickcraft or would 3M 5200 be more for my use? I split the boat into 2 parts to paint it and want some protection when it's ready for the water.
  13. krs60

    carb linkage

    I'm planning on rebuilding my carbs on my 1977 Mercury 850 85 hp. What's the ideal way to disconnect the linkage between the carbs? Is the linkage attached to the timing setup and if i remove the carbs do i need to reset the timing? My Seloc manual is not clear on the linkage at all, any tips or...
  14. krs60

    mercury 850 skeg guard

    Do they make skeg guards for a 1977 mercury 850 85hp? I checked the iboats marine store with no luck.
  15. krs60

    L78V vs L76V

    Is it ok to run the hotter L78V plug over the L76V plug on my 1977 mercury 850 85hp?
  16. krs60

    lower unit seals

    I want to replace the seals in lower unit on my 1977 mercury 850 85 horse. Water is getting into the lower unit, is there a kit or any special tools anyone recommends? I hear either the shift lever oil seals or the driveshaft seal needs a special tool.
  17. krs60

    how to replace throttle cable

    How do you remove the throttle cable at the motor (1977 mercury 85hp)? I see there is some type of clip the throttle and shifter cables run through that i cannot get to release. I want to save some money and learn more by doing it myself but i'm feeling a little mentally retarded with this...
  18. krs60

    Want to buy

    EDIT: Please read our rules, krs60. It could prevent a suspension. Thanks for your cooperation. :)
  19. krs60

    prop identification

    Looking for a prop for my 1977 mercury 850 85hp motor. 13 R 17 MWC is stamped into it, what exactly does that stand for? I'm guessing 13" diameter / 17 pitch? Does MWC stand for something about mercury?
  20. krs60

    where to get fuel line

    I have a 1977 mercury 85hp and need some really small fuel line, it measures close to 1mm inner diameter. Where do i find fuel line this small? The fuel line runs behind the switch box pictured. It runs from the fitting to the top left of switch box down to another fitting lower than the switch box.
Top