Search results

  1. A

    Battery Set uo and charging procedure?

    Battery Setup I have four batteries in my boat. 1 and2 are deep cycle and are maintained by a 2 bank on board charger. Battery number 3 is a cranking battery. Connected to that battery are the Outboard and electronics. The 4th battery is a cranking battery not used only serves as a backup. I...
  2. A

    What 2 cycle oil to use in 2004 TR6 150 HP

    I am getting a 2004 Mercury XR6 150 HP. 1) What 2 stroke oil should I use ? 2) I have a half gallon Evinrude XD100 left from my previous outboard, can I use that? Thanks, Andy
  3. A

    2004 Mercury XR6 150 HP- Opinions Good/Bad?

    I am presently looking at a bass boat that has a 2004 Mercury XR6 150 HP engine. How are these engines? Do I mix the oil with the gas or does it have a reservoir. Does it have a water separator filter? Thanks, Andy
  4. A

    Transom Bolt Clamp Handle

    I broke off one of the plastic handles that is attached to the clamps that secures the outboard to the transom. Are there any other ways of making a handle. Perhaps a thin bolt with treads on each end. Or installing a bolt head? any ideas? Thanks.
  5. A

    Does Etec 30HP use standard BIA holes for mounting to the transom?

    Does the Etec 30hp (2011) use the standard BIA holes for mounting the outboard to the transom? 12.87" Top 9.875" Bottom Thanks, Andy
  6. A

    Trim & Tilt Units?

    Looking to get a trim and tilt unit for my 30hp Etec. Any preferences as far as brand in concern? CMC.Panther,Atlas, Bob's Machine Shop? Thanks, Andy
  7. A

    Trailer Tire PSI?

    Size of tire = 5.30-12 On the sidewall of the tire it states "Load 1050 Mas Psi 80 psi. Should I really inflate these to 80psi? Presently I have them at 55 psi.
  8. A

    Trailing outboard in vertical position?

    How much clearance is needed to trailer with the outboard is a vertical position?
  9. A

    Trolling Motor Quick Release Plate, is it worth it?

    I am in the process of installing a TM on my boat. I was wondering if getting a quick release plate is a good idea? Andy
  10. A

    Mounting Trolling Motor on 14' Crestliner

    I am getting a new trolling motor. I am thinking of getting the Minn Kota Power Drive V2 or the Terrova. My question is will I be able to mount a Bow mount trolling motor on this? I know I will have to remove the mount and the outlet for the lights. The boat is a 14' Crestliner
  11. A

    Portable Gas Tank (different kinds)

    I was looking at portable gas tanks at a dealer. I didn't realize there are different types. One was the basic type, you open the vent when you are of the water. The other automatically vents itself. Are these worth the extra money?
  12. A

    What are some websites to get the best prices on Outboards?

    What are some websites to get the best prices on Outboards? Thanks, Andy
  13. A

    My Search is down to two outboards? Which one?

    I have my search down to two outboards. 1) 2011 Evinrude 25 HP Electric Start $3450.00 2) 2010 Evinrude 30 HP Electric Start $4072.00 Is the 5 extra HP worth $ 622.00 extra? Andy
  14. A

    Do I need to still use the Jack Plate?

    I am planning on getting a 25HP or 30HP Etec, long shaft. It will be replacing my Yamaha 15 HP. I had the Yammy on a jack plate to get the best performance. With the new outboard is it recommended the jack plate stays in for best performance? Advise. Thanks, Andy
  15. A

    Unmounting 15 HP Yamaha Outboard, need some tips.

    I am going to sell my 15 HP electric start outboard. I am going to take it off the transom tonight. The outboard is wired into a control panel on the back of the 14' Crestliner. How many wires am I dealing with? Do I just disconnect the engine wires from the control panel, fuse box, what ever...
  16. A

    Shaft Length/Transom Height, Confused!

    Presently I have Yamaha Outboard (Long Shaft) Model F15ELH mounted on a 20" Transom. In order to get the outboard installed at the correct height a Jack Plate was added. As you can see from the picture it looks good. Now the fun begins. I am planning on upgrading my outboard this winter. I am...
  17. A

    Rope Starting Etec? Hard or easy?

    The marina is offering a 25 HP Etec, Electric start and a 30 HP etec rope start. The rope start is 200 more. Is it tough to start the rope start? Is the xtra HP worth getting the rope start? Andy
  18. A

    Which Outboard to get?

    I am in the process of looking into getting a outboard for my 14' Crestliner Sportman's. Here are my choices that I am pondering: 1) Get new Evinrude Etec will cost me 1900.00 after selling my current motor 2) Get Used 2008 2 Stroke Yamaha, less then one hour of use.(will cost me 1300.00 after...
  19. A

    Choose, Evinrude Etc 25Hp Or Yamaha 4-Stroke 25HP

    Which would you pick and why? Evinrude Etc 25Hp Or Yamaha 4-Stroke 25HP Andy
  20. A

    Pull Start or Electric Start?

    Pull Start or Electric Start? Etec 25 HP Andy
Top