Search results

  1. Saginaw Bay

    Timing a '72 888

    Mine has the pin. I suppose the timing marks are on the flywheel. I am seeing marks but cant read them, I rubbed chalk on them and only a little better. I think I see a 0, and I think maybe a 10. I got it at what I think is the 10 and the 0 is above the pin not below it. Am I close given...
  2. Saginaw Bay

    loose connection on points.

    Was checking my points for proper gap. Noticed a loose connection connection the coil, and the condenser. Had the boat out the night before and noticed it was slow to plane. but still made 33 MPH GPS. (which i still think is slow) '72 slickcraft 19.5' 888 Prop: 15 3/4"x17. I also noticed...
  3. Saginaw Bay

    Load rite trailer question

    My 1972 slickcraft loads on my load rite trailer a little off center every time. Should I tighten the roller ubolts so that they cannot pivot, thus forcing the boat in position? ( side to side not front to back).
  4. Saginaw Bay

    Got some prop questions...

    OK I have a 1972 slickcraft ss195 19.5' I have a 15 3/4" x 17 prop on her now which get me about 32MPH GPS. It takes about 5 seconds to plane out. I am not sure what RPM I am running due to bad tach. I look in the manual and it lists the 888 15 3/4"x17 prop for being for a 20-25' boat. and...
  5. Saginaw Bay

    Tach question

    Ok, I think I got a bad tach. It does not seem to register between 0 and say 1200 RPM. I went today looking why....... I found some loose wires, tightened them up, still same. So I started grabbing,turning, and wiggling wires, nothing too serious, just trying to find a loose connection. Bam...
  6. Saginaw Bay

    Just making sure

    80-90W gear oil is indeed acceptable for my mercruiser one drive. Wanted to look at the old fluid. Emptied into mason jar, Got about 30-34 oz out of the drive. Looks good, no burnt smell, no water, no shavings.
  7. Saginaw Bay

    What kind of range

    What kind of range should I be getting with my slickcraft 195 SS with the mercruiser 888. 50 gal tank. Get up on plane, trim out, and back off to throttle enough just to keep on plane. just wondering.
  8. Saginaw Bay

    What would a bad condenser do?

    Basically I was running along, and BAM! no motor. I replaced the coil as it was leaking oil from it, still doing the same thing, Firing 1 time, then nothing. Wondering if maybe my condenser went bad also? It is raining cats and dogs right now and cant go outside to troubleshoot. thanks
  9. Saginaw Bay

    Running good, rough water, hit a wave.....

    Bam! no spark. fuel check!, Air check! spark? not really. By not really, I mean boat fires when WOT in neutral, but just for a second. Coil is now leaking oil. A new coil is in order ( can I get a coil from Autozone?) But I think the shift/throttle is the culpit here. In reading some...
  10. Saginaw Bay

    One more Ted Williams Question

    OK, I got it running in a trashcan of water. There is now an oil slick in the can, This cant be nortmal can it? The motor has not been run for about 23 years as we can figure.
  11. Saginaw Bay

    Ted Williams 7.5 HP need help

    I was just given a 7.5 HP ted williams 7.5 HP short shaft outboard. The plan is to use this as a kicker motor on my 19.5' slickcraft. I had this running in a tub of water today, but I have a few questions. OK #1 this has an internal or external tank, is the little valve on the right side(...
  12. Saginaw Bay

    Tach is slow

    My Tach is a bit off, Mercruiser 888 (302 V8) , I have checked all connections and they seem sound. When in operation I am seeing around 2500-3000 RPM'S, When at idle the tach is at 0. Anything to look at here?
  13. Saginaw Bay

    Should I be using lead additive in my Gas?

    I was just reading through the owners manual I downloaded. My engine is a 1972 302 (888?)V8. It states Detonation can be caused when using unleaded gasoline. Further states that valve damage may occur. Now, at WOT I get a backfiring condition through the carb, could this be caused by that...
  14. Saginaw Bay

    My 1972 SS195.

    Here she is Traded a shotgun for her... I think I did OK. I replaced the floor last year, put the seats in, and the prop is in for repair. This baby has a 15 3/4" 17 pitch prop. Does that sound right for this boat? IMG][/IMG]
  15. Saginaw Bay

    Got a few questions...

    OK, Here is my boat. A 1972 Slickcraft SS195. Equipped with a 188HP 302. I am not sure what outdrive this has. Also, when I took the prop in for reapir, I was told it was HUGE!! The prop is a 15 3/4" 17 pitch. I was told that A 15" 15 pitch would be about right. I dont know what my WOT RPM's...
  16. Saginaw Bay

    15 3/4" 17 pitch prop

    Why are these so hadr to find? Can I go with a 15 1/2 "? Will I notice a big difference? 4 blade vs. 3 blade? Pros and cons there. Thanks for the help.
  17. Saginaw Bay

    1972 slickcraft 195ss questions

    Hi, I am wondering if you smart people can help me. I traded for a 1972 Slickcraft ss195 this past summer. I put new flooring and carpet in it. I put new seats in it. However, I have questions. #1 I was told the motor is a ford 302, can I go to the auto parts store and buy valve cover...
  18. Saginaw Bay

    1972 Slickcarft

    Hi, I am wondering if you smart people can help me. I traded for a 1972 Slickcraft ss195 this past summer. I put new flooring and carpet in it. I put new seats in it. However, I have questions. #1 I was told the motor is a ford 302, can I go to the auto parts store and buy valve cover...
Top