Search results

  1. series60

    Installing Pertronix electronic ignition kit #2842 in an AQ125

    I've read everything I could find but still unclear about the wire connections for installing Pertronix electronic ignition kit #2842 in an AQ125 with Bosch distributor # 0231 178 017 JF4. I removed the old points, ballast resistor wire and grommet from inside the distributor and reconnected the...
  2. series60

    Mercruiser alpha Exhaust Manifold Riser Gasket

    How do I determine which Mercruiser alpha Exhaust Manifold Riser Gasket to use. Do I need a restricted gasket or open?
  3. series60

    AQ125A timing belt

    I'm fairly new to the AQ125A engine and was wondering if the timing belts breaks will the pistons hit the valves? Thanks for the info in advance. Bill
  4. series60

    Adjusting the up travel on VP 270 tilt mechanism?

    Anyone know how to adjust the up travel on AQ125A/VP 270 tilt mechanism? Mine stops about 1/8" from completely up. I'm afraid it won't clear the arm on the drive. Read the little snippet in the manual but really can't see where there is an adjustment.
  5. series60

    AQ125 water inlet hose

    Looking for part number for AQ125 water inlet hose. This is the hose on the inside that connects from the chrome pipe of the transom shield inside to the brass engine connection
  6. series60

    AQ125A exhaust bellows?

    Upon inspecting my AQ125 exhaust bellows (Volvo OEM) I noticed a very small hole about 2" in from the end and I was wondering if it was factory. The hole is about 1/16th of a inch and looks factory formed. Is this a factory weep hole ?
  7. series60

    O-ring for trim motor shaft on AQ125A

    Looking for the part # for the o-ring at the bottom of the shaft of the trim motor on AQ125A. Thanks, Bill
  8. series60

    AQ125 front engine support

    I know this has been discussed here before and as many have said - It's lasted 30 years. I am restoring a 1985 Monte Carlo by Ebco which the transom was gone and the entire boat needed a lot of work so I gutted it completely including cutting off the cuddy cabin. Rebuilt the transom and decided...
  9. series60

    VP 270 Transom shield seal

    Looking for VP 270 transom shield seal kit part #. The large shield o-ring and the six small bolt sealing o-rings.
  10. series60

    AQ125A electrical connector

    This is the main harness connector from my AQ125A/270. I would like to ID the 7 pins used in this connector and what each one goes to. Pins 1-2-3-5-6-7-8 are the only ones used. I pulled back the boot covering the canon plug and I see there are some pins with two wires connected. I'm getting...
  11. series60

    Intermediate shaft torque value

    I'm looking at the engine service manual for Intermediate shaft torque value. Manual states 'Intermediate shaft, forward ....50 Nm (5.0 kpm) (35 lbf. ft.)'. My question is the reference to 'forward' meaning the bolts that attach the Intermediate shaft to the engine? Thanks,
  12. series60

    AQ125A exhaust downpipe o-ring

    Trying to locate the AQ125A exhaust downpipe o-ring. Need part # or web address to order. TIA
  13. series60

    Trim in/down issue

    I'm back at the original issue I have with porpoising. My 1984 Mercruiser 305 powered 20' IMP likes to porpoise above 25mph. Shifting weight doesn't help. It improves when I use the tabs but I feel it would improve more if I could get the trim rams to retract completely. If I disconnect the rams...
  14. series60

    Sealant

    Re: Sealant I use tube epoxy for small holes and screw waterproofing. You can buy them most big box stores. Easy to use and no mess.
  15. series60

    1975 14' Mirro Craft Utility Rebuild

    Re: 1975 14' Mirro Craft Utility Rebuild Fish out of my 1970 MirroCraft going backwards all the time:)
  16. series60

    1987 Sea Sprite 225 SSB transom re build.

    Re: 1987 Sea Sprite 225 SSB transom re build. Here is what I ended up with when I replace my transom.
  17. series60

    Tiller handle

    Re: Tiller handle Like mentioned."It sounds like old grease and maybe dirt have gummed the handle up or the magneto plate is rubbing or tight." I would start by disassembling the tiller handle and clean all the old crud off it. Use a light grease on the wear points and reassemble tiller. If...
  18. series60

    1957 evinrude 10 hp, fuel pump conversion

    Re: 1957 evinrude 10 hp, fuel pump conversion Here is my pump mount on my 1959 Evinrude 18. Just a flat piece of metal.
  19. series60

    Throttle slow to back down 25905R (1979 25hp)

    I have an issue with the throttle not backing down from cruise. The carb butterfly will close under spring tension as it should but the rpms are very slow to return to idle. Can't pinpoint this issue. Motor runs great except for this problem which presents itself at very inopportune times. Had...
  20. series60

    Johnson 1968 33hp

    Re: Johnson 1968 33hp The black arrow points to a good grounding point.
Top