Search results

  1. S

    New windshield

    Looking for a windshield for a 21' open bow. Any ideas who might carry them? Been on line but haven't had much luck. Thanks in advance for any help.
  2. S

    Black Smoke/Poor Idle

    Went to look at a 2000 boat wit a 5.0GL VP. It didn't start that well but ok. Once started, lots of black smoke and poor idle. It was also loud. I'm sure the exhaust bellows is shot, but would that have any other impact? What could be causing the smoke? Thanks in advance for the help.
  3. S

    New Motor Needed

    I have the opportunity to buy a very nice 19' Chap. Everything is new except the motor. The owner tells me the motor is blown. Its a 5.7 Merc, he doesn't know the HP. Where can I get a used or rebuilt motor? How much do you guys think it will be? What HP is recommended? Anything else I should...
  4. S

    93 Cobra OD with tiny hole

    I just noticed a tiny hole on the starboard side just ahead of where you put the muffs. Its about 1/16 and perfectly round. And of course when you start the engine the water comes out in a stream. Is that normal? If not, can it be plugged with something? Thanks for your help.
  5. S

    Trim Gauge Problem

    VP 5.8 carb, sx OD 1996. Trim works fine but no action on the gauge. What should I look for? Second small problem, tach not working either. any thoughts? As always, thank you for your help.
  6. S

    5.7 Merc Stalls at Idle When Porpoising

    2000 Merc stalls after a minute or so only when porpoising but not when rocking port to stern. Otherwise idles and runs fine. Any idea why?
  7. S

    Carb Leak

    Model 2300 Holley 2 bbl. Did an R&R on the carb. Fired it up and all is well. Went to use it a few days later and now I see a slight drip. Are the only 2 places it can leak from the gas inlet line and the base? Also, when installing the gas line to the carb is a sealer or some kind of washer...
  8. S

    How to Remove Plugs from Ford 5.0 VP?

    Its obvious to me there is a special tool to get at these without removing the manifolds but what is it and where do I find one?
  9. S

    No Gas to Carb

    Engine is 1996 VP 5.0FLPNCS. 2 bbl Holley. Looking down the carb I don't see any gas going in. Pulled the lines to the carb from the filter and it was clear. Pulled thde line from the filter to the pump and it was clear. The connection on the gas tank had some rust so I thought it was a bad...
  10. S

    Need Carter fuel Pump Cross reference

    I have a 5.0FLPNCS and the SN is 4110139495. The boat is 96 but I think the engine is 95. I am told the pump I need is VP#3854053. I found a Carter #60389 and was told it fits a 93 302 Ford but I don't know if its a match and haven't found someone to be able to tell me sure. Hopefully someone...
  11. S

    Won't start?

    My son just got 96 boat with a VP 5.0FLPNCS and cobra SX OD. He tried it yesterday and ran for a while and restarted several times. Finally it came to a stop and would not start. After looking at it, I put in new plugs and water separator and also a new impeller just to be safe. Threw a little...
  12. S

    What engine?

    Just got this thing. Its a 96 VP 5.0 with the Cobra Sx drive. On top of the arrrester it says 5.0 Fl. The numbers on the engine are as follows; 4110139495 3868414 The drive number is; Sx-01 1 66 4112027557 3868395 Didn't know if they were long numbers or the label was too small...
  13. S

    Manual 4 VP

    Is there a place for a downloadable service manual for a 97 5.0 VP with a Cobra SX OD?
  14. S

    Whats the OD?

    My son just picked up a 1997 boat with a 5.7 VP and Cobra OD. How do I find out what Cobra it is? Thanks for any help.
  15. S

    Alpha OD

    94 OD won't go up unless you tap on it. Loose connection? Solenoid? Any ideas?
  16. S

    OMC Exhaust Bellow

    Easy question..is it necessary? I've been told you don't need it on OMC 4.3. If thats right, why is it there? The current one has a hole and I was considering not replacing. I am buying a new UJ bellow to be safe since I got the OD off.
  17. S

    Knock or tick?

    My sons boat. OMC, 4.3. Lift the motor cover and theres an odd sound. My son thinks it sounds like a ticking, not too loud. I think it sounds like a knock. Check the oil and its about 3/4 qt low so I add it. Its back on the trailer and about to take it out again and now the oil looks about 3/4...
  18. S

    Impeller Question

    Cobra OD - When installing a new impeller, does it matter which you bend the flaps when putting it into the cage? Sounds strange but the cage is oval shaped and of course the impeller is round.
  19. S

    Installing the OD

    Cobra OD. Removed and serviced and now can't get it on. Any ideas? The alignment tool goes in pretty easy although its tough to pull out. A friend thought it wsas suction from the grease. The OD goes almost all the way on and then hangs up just as the bolts are about to slide thru the OD. Any...
  20. S

    Pulling the OD

    OMC Cobra. Easy enough to pull the drive but what's after that? Is the bellows and gimbal easily accessable? And will I need any special tools?
Top