Search results

  1. A

    performance depending on boat load

    Hello,<br />I have noticed that my engine is having a hard time when boat is loaded in the stern. <br /><br />I made a experiment with a friend: <br /><br />First when he was sitting at the stern the engine was slow and hard to get going. There wasn't much happening when pulling the throttle for...
  2. A

    termostats

    Hello,<br />where do I find the termostats on my engine? I have a evinrude 110 hp, -89.
  3. A

    overheat?

    Hello,<br />I have a evinrude 110 hp, -89. When I was out for a ride last weekend, some alarm went off. Every 5-10 minutes after going 3/4 throttle the alarm went off. After a while the alarm stopped. Same thing repeated itself over and over. It sounds like the oil-alarm, but do the overheat...
  4. A

    two cylinders failing

    Hi,<br />I have a Evinrude 110 hp, -89.<br /><br />It seems as two of my cylinders are failing, the two lower ones(#1, #3 I think). I didn't find any old posts on troubleshooting this. Where do I start?
  5. A

    evinrude 110 won't idle

    Hello!<br /><br />Put my boat in the sea today after winter. Everything seemed to work fine, so I took her out for a ride. The engine acted normally. So, I started by going at slow speed for about 10-15 minutes, and then I run her a bit harder, about 1/2-3/4 throttle. Everything worked fine, but...
  6. A

    tilt and trim

    Hi,<br />my tilt didn't work at all and I found that the problem was the tilt/trim electric motor. Sp I changed it. Now, it will only go down. I have tried to change the polarity, and then it goes up, but not down so there is no problem with the motor. I have also switched the relays and it...
  7. A

    evinrude 110hp -87

    Hi,<br />when I go out for a trip my enginge feels a bit weak. It takes some time before it gives everything it has. I often have to make several attempts to get it to level. Once properly warm everything works just fine. <br /><br />I'm quite new to boats, so I'd appreciate som tips.
  8. A

    broken powertrim motor

    Hi,<br />it's seems as my powertrim electric motor is broken. I've dissambled it and it seems as there is som kind of shortcut within the solenoid. First, Am I right in my conclusion? Second, if I am right, is there anywhere I can find a used one?<br /><br />I have a Evinrude 110, -87.
  9. A

    trim/tilt removal

    Hello,<br />still having trouble with my tilt and trim. I tried connecting the battery directly to the trim-motor but nothing happened... <br /><br />So, if I want to replace the motor or repair it, I have to remove it. It seems to as if it is only three screws on each side. Can this be correct...
  10. A

    evinrude 110 trim

    Hello,<br />I'm having problems with my tilt and trim. It just clicks when I press up and down. <br /><br />I tried releasing the oil-pressure screw and I managed to lift it up. When I let fall down again, it stopped when i reached the two trim-cylinders.<br /><br />As I understand the two...
  11. A

    evinrude 110 power trim screw

    Hello,<br />I'm having troubles with my power trim. It just clicks. Until I find the problem, I want to mannually lower the motor. I thought I found the screw, but when I tried releasing the screw, nothing happened. <br /><br />1: Where is this screw supposed to be? <br /><br />2: I read that it...
  12. A

    Power trim motor, manually

    Hi,<br />I'm having trouble with my power trim motor. I'm troubleshooting at the moment. <br /><br />The thing is, I want to lower the motor manually, so we can go out in the meantime. I know there is a screw on the motor for doing this, and I think I have found it. Now to my question: <br /><br...
Top