Search results

  1. F

    J40TELEUC constant alarm with key on cold engine

    No, no VRO installed. Buzzer has 2 wires from System Check monitor, one power the other goes back to the SC gauge, so any grounding is probably occurring in the SC gauge. VRO is disconnected, temp sensor is disconnected. Since sound is not at full volume, could there be a current leak within the...
  2. F

    J40TELEUC constant alarm with key on cold engine

    Disconnecting temp sensor has no effect. Buzzer has constant beep when key turned on, but also louder single beep heard when key initially turned on. Louder single beep seems like it would be the system check beep. System check gauge cycles through lights, then all off, but continuous beep...
  3. F

    '86 150 dies at idle

    This engine run a fine at all speeds above idle. It will idle fine for about 30 seconds, then it goes poof & dies. It starts right up again (with choke) & will idle if choke is activated for 3 seconds every 20 seconds or if the manual choke is is pulled out almost all the way. Idle speed is...
  4. F

    1990 120 water pump oring

    I replaced the water pump & have an o-ring left over. I put one between the cup & housing, one between the ss wear plate & impeller . Where would the 3rd one go? I found an old one on the floor where I removed the lower unit but I don't remember one falling out when I removed the gear case.
  5. F

    '87 Yamaha 150 Tilt/Trim motor

    The brushes on my tilt/trim motor appear to be causing intermittent problems. Has anyone replaced the brushes or is buying a replacement motor the best way to proceed? Thanks.
  6. F

    '87 Yamaha 150 Oil Alarm at startup-goes off eventually

    After sitting for a week or so, the oil alarm will sound when starting up my '87 Yamaha 150. Plenty of oil in aux. tank. After several startup/shutdown cycles, it goes off and causes no problems until it has set for a week or so. Any idea what I can do to keep this from happening? Thanks. Marlin
  7. F

    Johnson 120 Intermittent No Start

    My Johnson 120 (model J120TLESB S/N G02569565) has been having an intermittent issue. It will run for 10 minutes to 2 hours (the longest I've run it without shutting it off) , but when it dies it will not re-start for 10 minutes to 3 hours. It always starts right up after extended stops, like...
  8. F

    1990 Johnson 120 new alarm horn still doesn't work

    I replaced the alarm horn with a new one last night. It didn't sound when I turned the alarm on, so I traced the ground wire to the switch and the screw was loose, so I tightened it and then the alarm would sound briefly when the key was turned on. I made sure (twice) that the brown wire was...
  9. F

    How to waterproof Lund Pro-V console storage

    I have a '91 Lund 18' Pro-V with a single aluminum console. There is a tackle storage unit on the forward side of the console that has an overlay door. Since the console slopes rearward, any rain or spray leaks into the tackle trays. The door is 7"X21". How can I add a seal to this door to keep...
  10. F

    Alarm module for 120 Model J120TLESB

    The local marine repair shop is telling me that this motor shouldn't make a "beep" when the key is turned on. All the posts I can find indicate that this should occur when the key is turned on. I've posted before asking for the part number for this alarm module, but the number that was provided...
  11. F

    Need part number for 3-wire alarm module

    Could someone provide me with the part number for the 3-wire alarm module that's located in the console. Alarm is for a 1990 Johnson 120. If you have a preferred site for purchase that would be appreciated. I can't seem to find the correct diagram on any of the Johnson parts site. The alarm...
  12. F

    VRO oil tank circuit board repair

    Is it possible to re-flow the solder on the circuit board in the oil tank or is it sealed in epoxy? My '91 120hp sounds a constant alarm when the key is turned on, and I think I've narrowed the problem to the oil tank electronics, but I can't find any internet postings about repairing the...
  13. F

    '90 Johnson 120 Oil Level Alarm

    I'm getting a continuous alarm when the key is turned on (engine off). Unhooking the tan wire at the alarm silences it so I think the alarm is ok. Unhooking the tan wires at the heads (what I think are the high temp sensors) does not stop the alarm. Disconnecting the tan wire from the connector...
  14. F

    How to prep epoxy coating for carpet adhesive

    Plywood has been dried and epoxy coated. What is the next step before applying the carpet adhesive? Should it be wiped with acetone and/or sanded? I'll be using a latex marine carpet adhesive and marine carpet.
  15. F

    Epoxy Drying Time

    I'm putting a new deck in my '91 Lund 1800. I dried the exterior grade ply in my basement several months last winter. I mixed the epoxy in the proper ratio using a graduated container and rolled it on the ply, even raising the room temp to 80 degrees with an electric space heater. A week later I...
  16. F

    Seal for top of livewell on 1991 18' Lund Pro-V

    I'm replacing the deck on this boat. The front livewell has an access hatch in the deck, the livewell plastic tub is actually pop-riveted to the aluminum stringers, and there is a putty-like "tape" (flat, 1" wide, 1/16" thick, uniform width, flakes off like putty when pulled up with fingernail)...
Top