Search results

  1. C

    Prop

    I am looking for a prop new or used for a 9.5 Evinrude. it is 8 1/4 x 8 1/2. where might I find one Thanks Jeff
  2. C

    Steering for 68 9.5 Evinrude outboard

    I want to make my 1968 9.5 motor remote steering. I have the bracket that attaches to the motor so that the a cable and pulley set up can be used.. I want to also only have the cables run down just one side of the boat. So I am looking for some help with how and where the cables will be run...
  3. C

    Owners manual 1968 Sportwin

    I have a 1968 9.5 Evinrude Sportwin that I bought this summer and I am looking for a service manual and owners manual. Where might I find these. cusoak
  4. C

    95 90 hp overheating

    I am wondering where I can find a water flow drawing for a 1995 90 hp Johnson Mine is over heating, thinking a clog some where, but don't know where to look. If I had a drawing may that would lend some insite as to where it might be clogged. Jeff
  5. C

    Over heating

    I have a 1995 90 hp johnston motor that the heat alarm goes off. At first when I fired it up and ran it some the alarm went off. It was puttin out waster through the pee hole. Found that the left cylinder was hotter than the right one( standing at the back of the motor So I pulled the...
  6. C

    1961 45 hp Merc crankshaft seals install

    I think that my 1961 Merc 400E needs the upper and lower seal replaced. I am having trouble with it idling in gear. It will start and idle and when shifted in to gear it dies. Have had it adjusted tied to the dock. Can get it to work all right there but then after a run it will still nott idle...
  7. C

    Not running right

    I have a 1995 Johnson 90 hp outboard. Early this summer it developed a problem, when going at full throttle it will run ok and then just die down and stop. Sounds like some one turned off the fuel to the motor. It will start back up with no problem. If run at about half throttle it will run fine...
  8. C

    Under the deck fuel tank

    I am going to put up front in the boat I am building a 12 gal under the deck fuel tank. The motor I have is a 1961 45 hp merc. I need to know what would be the right size fuel line to run to the motor and where would I find the part # for the bouynet fitting for the motor. The fuel tank will be...
  9. C

    What size battery

    For a 1961 45 hp Merc what size cranking amp battery should I buy. Jeff
  10. C

    Getting read to see if it runs

    I want to see if my 1961 Merc runs. What would I need to do to make sure I don't damage it. Like the water pump. Jeff
  11. C

    Electric Choke

    I was wondering if you could ad an electric choke to a 1961 Merc. 45 HP. S/N 1308416 The control box that I have has a push button on the back top for the choke. Right now it is manual. Thanks Jeff.
  12. C

    Steering linkage merc 45 hp

    Re: Steering linkage merc 45 hp I found this pic of a merc that looks just like mine. If you look close you will see what looks like an other tilt tube hooked to the existing on with brackets. I appears to be out front of the motor a little ways. How do you think that might work.
  13. C

    Steering linkage merc 45 hp

    I have a 1961 Merc 45 hp motor, that I need help finding a pic or parts list of the steering linkage that fits on the motor. I have a Teleflex steering assembly and cable. The serial number of motor is 1308416. Thanks Jeff
  14. C

    Mounting Merc Motor

    Yesterday I mounted my 1961 45hp Merc to the transom on the 14ft Glen L boat that I am building. After cutting the transom down to allow the cavation plate to be even with the bottom everything looked great. Then I looked at it from the side and noticed that in the down position the motor did...
  15. C

    Throttle and wiring controls

    Hi I have a 1963 45 hp Mercury outboard. The motor came with 3 sets of controls. How could I determine which one would work. They all have the same number of holes in the wiring plug that match up with what the motor prongs. They also have the same choke buttom. They also have a release arm...
  16. C

    Power trim pump

    I am trying to find out what make of power trim pump was put on a 1971 Glastron model CV16 Could anyone help me. Want to find out if it works. Thanks Jeff
  17. C

    Manuals

    I am looking parts service and operators manuals for 1961 400 mercury outboard Please let me know where to find them Thanks jeffi
  18. C

    Mercury 400

    I am now the owner of a 1961 Merc. 400. It has a2 blade brass prop. I was wondering what the hp would bed and how much it weights. It is part of a doner boat 1971 Glastron. Also where will the serial 3 be. Thanks Jeff
  19. C

    1975 40 hp evinrude

    i have a chance to buy a 1975 40 hp with comtrols. manual shift do not know the model. it does run. Need to make an offer what would be a fair starting price. Jeff
  20. C

    Identifying old Evinrude out board

    I just purchased an old Evinrude. the only numbers I could find were 4178-0652. This was on a plate that was just below the engine. It has a small 2 blade prop. Open rope pully to start it. Took some of it apart to get to the spark plugs and found that there were 4. It took 2 different size...
Top