Search results

  1. N

    Johnson 2hp engine temp

    Hello my 1984 Johnson 2HP runs good and pumps out nice water. I did notice that the exhaust side of the cylinder is hot to touch . My temp gun says 130 degress Fahrenheit at about idle and 170 degrees Fahrenheit about 3/4 engine speed on the exhaust side. It runs good but I never noticed this...
  2. N

    Yamaha 2HP water pump impeller part number

    Hello I was looking for the sierra part number for a 1985 Yamaha 2HP water pump impeller. any help? thanks john
  3. N

    Johnson 2hp 1986 water pump impeller

    Hello , I have a Johnson 2hp outboard 1986 and I am looking for the part number for just the water pump impeller. I would like to replace it this year. thanks john
  4. N

    Evinrude 1953 7.5hp

    Hello i was running my 1953 Evinrude 7.5hp which i bought 1 year ago and put it back together.I thought it might be running hot,the water pump looks good and there is plenty of water coming out of the Pee hole in a barrel.When i shut off the engine,it looks like steam coming out of the Pee...
  5. N

    evinrude 9.5hp 1973 shifting

    Hello i have a 1973 evinrude and it doesnt shift into forward but neutral and reverse work fine.When i shift it into reverse,there is a poitive feel and you know it went into reverse! When i move the shift lever down to the forward position, there is no distinctive feel that it went into...
  6. N

    Eviinrude 9.5hp 1973 fuelline

    Hello I just picked up this evinrude 9.5hp and my fuel line on my tank doesnt clip in.It almost does.The fuel connector that sticks out of the cowling is just a little bit short.Is there a way to adjust it?? I use this fuel tank and line with my other evinrude outboards. thanks
  7. N

    EVINRUDE 9.5hp 1973 shifting problem

    Hello my Evinrude 9.5hp will not shift into forward.Neutral and reverse work fine. I tried the adjustment for the shift lever next to the flywheel.I believe the problem is in the lower unit.Before i tear into it,any ideas what to look for?? thanks john
  8. N

    Evinrude 1973 9.5hp sportwin shifting

    Hello i bought an evinrude 1973 9.5hp that was all apart. I put the engine together and lower unit back on,cleaned the carb ,cleaned the points and the engine now runs great!!I am getting a new head gasket,water pump and thermostat for the ebgine. My issuse is how to set the shifting. It...
  9. N

    Johnson model RX-12M????what is it

    Hello my friends has a two clyinder Johnson model RX-12M s/n J2455074 Anybody know the year and HP?? we believe its 28hp?? Where can i get information on that engine? thanks john
  10. N

    Evinrude 1966 5HP fuel pump repair lit

    Hello do anyone know a sierra part number or where to get a fuel pump repair kit for an Evinrude 1966 5HP Angler engine? thanks john
  11. N

    Evinrude 5HP Angler

    Hello i just picked up an Eninrude 5HP 1966 model # 5602R. I took off the flywheel and She looks like she has new coils and has a nice spark! The carb was very clean so I started her up with a rope.The pull start spring is broken and needs to be replaced.I have the spring out but was wondering...
  12. N

    Evinrude 4HP ??? Help indentify

    Hello i may buy this evinrude from a guy for $50 but he knows nothing about it. I believe its a 4HP. I dont see a lever on it for a throttle? Could it be missing? I also think thats its an always in drive engine. The engine turns over.Any information on this little evinrude would be appreciated...
  13. N

    Evinrud ELTO

    Hello i have a chance to pick up an Evinrude Elto motor.Its s/n 4301-04152 which I believe is a 1939 1.8hp. It's in rough shape and needs TLC. Any idea on how to get parts and is this motor called the ACE? was it pretty common? thanks
  14. N

    evinrude 1953 7.5hp head gaskey

    Hello i am looking for a part number for my evinrude 1953 7.5hp head gasket. thanks john
  15. N

    Chrysler 4 hp carb / ignigtion timing

    Hello, I have a 1981 Chrysler 4hp. i have a manual for it and it has every part and part number in it for the entire engine,specs,ignition timing.My manual says 1 5/8 air screw for a starting position to run, than fine tune. There is no mention of the mark on the throttle cam for the throttle...
  16. N

    Chrysler Ignition Carb timing

    Hello, i have a 1981 Chrysler 4hp in very good condition. The engine has good compression,nice spark,clean carb and fuel tank.Ignition point gap is set.020". It will fire but will run terrible and run only for a short bit,15 to 30 seconds than dies out.Spark plug does look wet so i think its...
  17. N

    chrysler sea king 4hp infomation

    Hello i have a chance to get a chrysler seaking 4hp,1981. Any idea on how parts are to get.It needs a prop and doesnt run but pulls over with good compression. I dont see any used parts on ebay for this engine. I have Evinrudes from the 50,s and get parts all day long. Any info??? thanks john
  18. N

    chrysler seaking 4hp 1981

    Hello i was wondering how good these little engines were? I am really an Evinrude person but i came across this chrysler 4hp seaking. There is no prop on it,any ideas where i can get a prop and are other models interchangable? also are parts common for these little engines? thanks john
  19. N

    New 3 gallon gas tank Vent???

    Hello i bought a new 3 gallon plastic fuel tank from West Marine. Everything on the tank is plastic. My tank builds up pressure in it from just sitting around in the sun.I unscrew the vent cap and no air comes out.I than loosen the main cap and the air comes out. I went and got another new cap...
  20. N

    Evinrude 1953 7.5hp carb

    Hello,i have a 1953 Evinrude 7.5hp. I am looking for the needle and seat part # 276914 for the carb. It has the stock carb,Tillotson on it .I called a couple of places and no luck yet.Any ideas where to find the parts? thanks john
Top